10654783803 Kenmore Refrigerator - Instructions

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Ordered gasket through this site pulled old gasket off, because my conquest had no screws on lining, Put new gasket on top and bottom first and kind of forced the edges into groove using heat gun cause gave me a little problem. But overall, it worked to perfection! Now to buy other gasket for refrigerator door!

By following your information

I ordered two new ones from partselect.com. I figured if I was replacing the one for the refrigerator door I might as well do the freezer door too.
Very easy to take the old ones off, take the putty knife clean tracks out. Putting the new ones on, was a little harder to do. You have to start in the corner and push the gasket into the slot. You need strong hands to do this. Once I heard them click in, they guided themselves the rest of the way. Once they are on, check to make sure they touch the frame of the door. My freezer was perfect, but the refrigerator had an area of 25 inches that did not touch the frame. I called partselect.com and they sent out another new gasket for the refrigerator door. (I had to pay for this one but was told once I mailed in the defective one, they would credit me the cost of the returned one) I took off the bad gasket and installed the 2nd new gasket and that one was perfect.

Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

This story is less about the repair than the service. On Monday, I removed the meat drawer to give it a quick rinse. Unfortunately, I fumbled the ball getting it back to the fridge, dropped the drawer on the hard stone floor, shattering it.

Instead of calling a repair man or going to the local appliance store, I opened up my macbook, found partselect.com, ordered the part and they had it taken care of in 5 minutes. Two days later, Fed Ex handed me a box with the replacement drawer, and I slide it in. Done. Total time to repair -- 6 minutes.

Sure beats leaving the house!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

The cap will only fit on one way. Align with tabs on filter, twist on. Press the filter into place and press to seat. Locks into place.

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

unplugged the power and removed the cardboard back Unplugged the part and power from the side of the compressor Plugged the power and new part back in to the side of the compressor and replaced the clamp Plugged in the power cord to the wall outlet and the refrigerator started to hum Job done Thanks

removed door took out single bolt pried out cam put new one in returned bolt rehung door. 15 minutes

pulled old gasket out cleaned area where gasket was and lube edge of new gasket with vaseline starting at top slide gasket in then sides last was bottom which was hardest. 20 minutes

I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.

We emptied out both sides, refrigerator and freezer, and followed the instructions in your video. We turned it off and disconnected the power. We took off the freezer door first. It made it much easier to get the shelves out and reach way back into the freezer. We removed the light and cover, then the ice auger motor. The back panel was easy to lift and remove. The wire assembly was a little hard to understand at first, but when we figured it out it was easy to remove and replace the bimetal defrost thermostat. We did check the video when we had the wire harness out, to make sure we got it right. We reassembled the freezer's inside parts and reattached the door. Before we turned the power back on, we scrubbed down the entire refrigerator. When we turned the power back on, the refrigerator and freezer were operating quietly - no sparks or explosions or shorting out - hooray! And the problems were solved.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.

Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.