25355333600 Kenmore Refrigerator - Instructions

I ordered the parts by studying the diagram and they were perfect. Thanks for making it so easy.

Followed instructions for this part from this site and things went well.

The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!

It was simple. I loosened the two screws holding the ice maker unit. Then disconnected the wire harness. Plug in the new ice maker and tighten down the two screws. Held reset button for 15 sec. Done! took ten min. I had a full try of ice the next day!

Replaced the Triple Water Valve

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

First I obtained the manual to the refrigerator. I identified the screws to be removed. I turned off the water then unplugged the water lines. I then replaced the Water Filter Base and reassemble the parts. Within minutes of turning on the water, water and ice making had returned. I was a hero for saving the family $200 in parts and labor.

Looked at video on how to remove and reinstall support and followed the instruct ions

Remove shelves and rear panels to get to motor. Motor is held in place on shroud by simple strap. Remove fan blade, then un hook strap, remove and save rubber spacers on old motor to reuse to remount new motor. New motor Mew motor has wiring harness that is universal. Cut out the three wires that go to the new motor leaving long as possible, cut wires from old motor as long as possible, strip ends of all wires 1/2 inch, connect wires by color,slip into provided wire connectors and crimp. Pull on wires to insure connection. Tie wires together so they don't touch the coils. Plug in and check operation. If all is working unplug and replace all covers and shelves. Plug back in and it will take few hours to reach operating temperature. Video of side by side repair shows easy removal of panels and motor.

Emptied the shelves off door and pulled door off fridge swet on counter and took out old plug and put new one on.

Glue the old one with gorilla glue. Made space and put the bin in. Now I have an extra one.

The repair could not be completed. I ordered a thermostat defrost kit but received a collar arbor for a saw. They do not answer the phone at customer service and the order took close to two weeks to get in the first place. Beware of shopping at this site!

I had to remove the face cover to gain access to the ribbon harness, also had to remove the push pads The ribbon is a delicate item so care had to be taken not to bend the ends. The ribbon can fit either side so getting it in place to make contact was kind of tricky. After the ribbon was in, it just a matter of putting things back together. Dispenser is fixed at a minimum cost, ribbon was shipped within 2 days which was great. Thanks to Part Select for easy to find on the net, had a complete diagram of the refrigerator ice/water dispenser so finding the parts needed was simple. Doug

I ordered 3 bins initially and received only one, which was very easy to install. It just snaps in. When I called to indicate that I had received only one of the 3 bins, a claim was submitted and I got a refund for the missing parts. Then I had to reorder the two missing parts.

When I received the reorder, both of the bins were broken. I called to indicate that they were broken. I was told that I would have to submit photos of the broken parts to photos@replaceparts.com, which I did. After I submitted the photos, I received an email asking me for the photos again and the serial number of the refrigerator. This is the first time the serial number was requested. I have no idea why they wanted the serial number at this point instead of when I first ordered the parts.

At this point, I am still waiting to get my claim for the broken parts approved. I assume that the shipping department is pretty worthless, since they screwed up my order to begin with and then the shabby packing that was done for such fragile plastic parts on the reorder.

I'm not happy with the hassle that I have been going through just to get a simple order delivered.