10664269401 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Darlene from Philadelphia, PA
- Parts Used:
- WP2254473
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
I had taken freezer door off when moving and misplaced the one of the hinges.
I attached the hinge and secured it with screws and socket wrench.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Colorado Springs, CO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer and refrigerator compartments not cold enough
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Xiaoping from KIRKLAND, WA
- Parts Used:
- W10854037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no drawer
just insert
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MCFARLAND, WI
- Parts Used:
- WP2254533T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The existing handle broke at the top
I'm so glad you asked! You sent a SUBSTITUTED part which came nowhere near fitting the refrigerator. You have, so far, ignored three emails in which I requested a refund for the part as well as the shipping both ways. Since you sent something I didn't order, and it didn't do the job, that seems only fair. Evidently you guys don't agree. I don't have any problem with the fact that you probably sent something you THOUGHT would work - my problem is that you seem to feel that it's my mistake, so shipping costs ought to be on me. I will continue trying to get this issue resolved, but I really hope you do print this on your website. I'm not certain why you have a customer service address when no customer service exists. I am very disappointed with this whole transaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from FORD CITY, PA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer occasionally had a temperature alarm.Clicking noise also.
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from GLOVERSVILLE, NY
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Plugged it in.
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lamar from American Fork, UT
- Parts Used:
- WP2314549
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Shelf broker which holds the crisp drawers
Wife did the replacement of the the plastic part very easy to do. I was very impressed with the speed in which the part was delivered to my home after it was ordered. Thank you very much. Lamar.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MATTHEW from STOCKTON, CA
- Parts Used:
- 4387478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Light Socket Burned Out.
I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Lakewood, CA
- Parts Used:
- W10854037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My Crisper Pan was broken so I needed a new one.
I ordered a new one waited for the new ones to come in once it did I took out the old ones and replaced them with the new ones. It was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from OJAI, CA
- Parts Used:
- WPW10421486
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The fridge was missing the lower shelf bar on the door
The bar slipped right into a groove on each side and took less than 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Lancaster, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
compressor not running
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- asberry from SAINT LOUIS, MO
- Parts Used:
- WPW10189703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
first a loud noise than noise stopped then the refridg. stop cooling like it should
after finding out what could be the problem I order my part which I got around 3 days unboxed it and replaced it in the freezer component which I had already dismantled made note how I took it off and replaced it in the same way took about 25 to 30 minutes quite easy for me was grateful for the solution and proud of myself after replacing it and it began to work now it's freezing and getting cold as it should Thank you my part store
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Regina B from ST MARTINVLLE, LA
- Parts Used:
- WPW10421486
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Missing retainer bar for freezer shelf
Retainer bar was a little long but husband used a saw to make smaller (the part said it was a similar to my model- Maytag no longer made this made) It was perfect -- ow I have a whole new usable shelf!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from DONALDSONVLLE, LA
- Parts Used:
- W11745278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door hinge broke.
Removed door and replaced bushing bracket was ok.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie E from MODESTO, CA
- Parts Used:
- WP4387503
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Freezer was working but fridge was barely cooling. Look further into how to test thermostat.
I just replaced my defrost thermostat after using the place-in-ice-water method, and I think it may not have been necessary. My timeline: my fridge was not getting cold enough. I realized it the day before going on a trip. I vacuumed the (very dusty) coils at the bottom, and the next morning the fridge seemed colder, but I thought I should order parts just in case. I ordered a heater and a thermostat. The fridge seemed to be operating normally when I returned from my trip, but I had the parts, so I thought I'd go ahead and dismantle the freezer and test the existing parts. My intention was to return both parts if the old ones passed the tests. I opened up the back of the freezer and there was no ice on the fins. I thought, great, the existing heater works! I cut out the thermostat, placed it in ice water, and didn't get continuity. So I decided to go ahead and put in the new thermostat. Because I'm not experienced with using a multimeter, I thought I'd test the new thermostat to see how the test should work. To my surprise, the new thermostat also failed the test! Stumped, I thought I might as well install the new thermostat, since I had opened the package and couldn't return it.
Further internet research suggests the place-in-ice-water method of testing is not adequate. One YouTube video by Parts Dr says to place the part in a working freezer. I froze my old thermostat and tested it; still no continuity. This thermostat may not be typical, though. The video discussed the temperature ratings on thermostats. The temperature rating on both (old and new) thermostats is L8.9-16.7C. That converts to 48-63 degrees fahrenheit, which obviously are not freezing temperatures. I'm not convinced I needed a new thermostat, but I trusted the videos I consulted earlier.
I cleaned the fridge thoroughly, so at least now I have a nice clean fridge to show for my efforts.
Further internet research suggests the place-in-ice-water method of testing is not adequate. One YouTube video by Parts Dr says to place the part in a working freezer. I froze my old thermostat and tested it; still no continuity. This thermostat may not be typical, though. The video discussed the temperature ratings on thermostats. The temperature rating on both (old and new) thermostats is L8.9-16.7C. That converts to 48-63 degrees fahrenheit, which obviously are not freezing temperatures. I'm not convinced I needed a new thermostat, but I trusted the videos I consulted earlier.
I cleaned the fridge thoroughly, so at least now I have a nice clean fridge to show for my efforts.
Was this instruction helpful to you?
Thank you for voting!