59668943800 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Arthur from WYNNEWOOD, PA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rail snapped
Followed video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lionel from Watertown, NY
- Parts Used:
- 4396418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Icemaker not installed in refrigerator
I followed the instructions for the installation of the icemaker and its connection to the house water supply.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor R. from BROOKLYN, NY
- Parts Used:
- WP67006531
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Stead flow of water from under the refrigerator
Unplugged and disconnected the water supply.Disconnected the water line coming from the filter and cut about 1/8 inch off to square it off.
Unscrewed panel to expose inlet valve. With a marker I noted where the lines need to go back to. Disconnected the other two lines and made fresh straight cuts with a utility knife. Disconnected both plugs from the old inlet. The yellow one was difficult to get off, so I carefuly used a screw driver. Be careful, you don't want to break the plug. Reinstalled the new inlet. make sure that you push all of the lines in the valve so that they are completely seated. Make electrical connections. Secure valve to the panel. The water line from the filter should be the last line that you connect. Put screws back in the panel.
Plug in and turn on water supply. Fill up a gallon container from water dispenser. Check for leaks. Let the ice machine fill up. Check for leaks. Place back panel back on and secure. GOOD LUCK!
Unscrewed panel to expose inlet valve. With a marker I noted where the lines need to go back to. Disconnected the other two lines and made fresh straight cuts with a utility knife. Disconnected both plugs from the old inlet. The yellow one was difficult to get off, so I carefuly used a screw driver. Be careful, you don't want to break the plug. Reinstalled the new inlet. make sure that you push all of the lines in the valve so that they are completely seated. Make electrical connections. Secure valve to the panel. The water line from the filter should be the last line that you connect. Put screws back in the panel.
Plug in and turn on water supply. Fill up a gallon container from water dispenser. Check for leaks. Let the ice machine fill up. Check for leaks. Place back panel back on and secure. GOOD LUCK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from LOUDON, TN
- Parts Used:
- WP67006877
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
broken glass shelf
Replaced shelf, very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from ZUNI, NM
- Parts Used:
- W10613606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Refrigerator went out during blackout.
Installed the part, fan turned on, lights on, however, the freezer did not get cold and refrigerator is not working at all. Need advice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from VINTON, VA
- Parts Used:
- 4396418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice maker leaked
Removed refrigerator door. Removed 3 screws. Replaced old ice maker with new ice maker. Put in 3 screws. Ice maker working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from HUNTINGTN BCH, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Difficulty removing old switch.
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AUBURN, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Wilmington, NC
- Parts Used:
- WPW10671238
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken center crisper rail
I took all items off the glass shelf. Removed the two crisper drawers. Removed the glass shelf. Installed the center rail. Replaced the two crisper drawers, the glass shelf and all items. Job done in less that 1 min. Thank you for great customer service and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from HOPATCONG, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light rocker switch broke and refrigerator light couldn't go on.
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PORT JERVIS, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problems
Just plugged it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel F from CALEDONIA, MN
- Parts Used:
- W11613295
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer and refridgerator just stopped working.
The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.
The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!
The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from SHEBOYGAN, WI
- Parts Used:
- WP67006877
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old glass broke , new glass fit perfect
Just set the glass shelf onto frame perfect fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royal from RICHMOND, VA
- Parts Used:
- WP67004028
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
New Ice maker was install but technician failed to transfer arm off old ice maker and put on new one..
Work was done by service tech. I ordered the arm for my mom to save time when tech came back to do the job correctly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Hammon, OK
- Parts Used:
- WP67006531
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Water in door valve was leaking
Removed rear access removed valve mount turned off water supply Unplugged out of the wall plug removed the two electric plugs removed the three water lines installed the new valve in reverse order, check for water leaks worked perfect
Was this instruction helpful to you?
Thank you for voting!