59679543013 Kenmore Refrigerator - Instructions

Took the food out. A couple of screw removals. Put drawer lid on and then put the screws in. Nothing to it.

Wasn't a big deal. Removed the the shelves and glass immediately above the endcap as well as the large 'goumet' draw. Used a nutdriver to remove two screws. Popped off the old endcap and did everything in reverse. Replaced the long clear goumet draw cover that was still intact. Thanks for making it easy!!!!

Took off old one and just replaced new, very easy and corrected problems!

It took longer to empty the items off the shelf than it did to do the repair. Slid the veg, drawers out, set them aside.Took glass shelf out set it aside. removed three screws with 1/4in socket. Removed end cap. replaced with new end cap, replaced screws, cleaned and replaced shelf and drawers. Was a very easy task. these pegs break very easy, this is the second time I have had to replace the end cap, both times it was the left size. problem is you have to buy both the left and the right side together,

I replaced both side. The left side I very easy to replace. It has 2 screws holding the end cap in place and the tracking has 2 screws holding it in. Undo the 4 screws and put the track on the new end cap and then you are good to go to install the new end cap on the left side. Now for the right side is easy, but you now have to also undo 2 screws and other 2 for the track just like left side but also you are going to have to undo the humidity control stuff and put it on the new end cap.

Really easy - Remove drawers, remove glass shelf and associated support rails, remove drawer slide from old endcap, remove old endcap, reverse proceedure installing new endcap - now the hard part, have a cool softdrink while you carry the old endcap and packing material from the new one out to the trash.

By the way - the part got here really fast - thanks for the great service.

Part was pretty ubiquitous so plastic door pins part fits a lot of refrigs, no tools necessary, new part is flexible enough to bend slightly to fit over pins at side. Mine was a bottom freezer type.

took out the drawers and glass shelf and unscrewed the sides took parts for drawer glide off put them on the new part reinstallled saved $110 service cll and $20 on the part!

Two phillips head screws out to remove drawer slide. Three screws to remove right side drawer support. New support placed, new lid snapped into place. The right side has an adjustment lever. Re-routing that took the longest. The arm had to be removed and twisted to get the adjustment knob off and on.

Receive part in two days. Super fast.
Repair was very easy. Whirlpool designs so even the "average joe" can fix it. Took abour 20 minutes to repair. Even with no directions.

this pantry lid was warped when the fridge was new. tolerated it for a while finally it cracked then worked pretty well for a couple years until the RH hinge pin (part of a support for the pantry door)broke. I had never bought parts from partselect.com before, but I have in the past bought repair parts from other sites. Partselect.com had drawings of the refrigerator parts that although were a little hard to see were adequate to tell what parts I should order. I ordered the parts, they came in after an acceptable wait. The parts were literally perfect, went right in, and everything is working quite nicely. I am happy with Partselect.com and will probbly go to them first in the future. I actually like the refrigerator a little more now than I did when it was new.

I ordered the part and it arrived in about 5 days. I removed the two lower crisper drawers and the glass shelf seperating these from the Wide-N-Fresh compartment, to give me room to work. I removed the two screws holding the right side endcap in place. The temperature adjustment mechanism was a bit tricky to remove from the broken endcap and replacing it on the new endcap. Once that was figured out everything fell into place and the lid was snapped into place and worked properly

I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!