25344503603 Kenmore Refrigerator - Instructions

Installed a new Defrost Thermostat.

Unplugged freezer, used digital multimeter to test defrost thermostat, temperature sensor, start/run capacitor and start/run relay for compressor motor. Found ohms values for start/run capacitor to be out of range and carbon traces on relay base where capacitor connects. Replaced capacitor and relay. Plugged freezer in and compressor immediately started running. On mid-range temp setting, empty freezer, temperature alarm light went off in 3 hours. Freezer has been functioning properly since repair was made. My husband is a licensed elevator mechanic with a background in electrical troubleshooting. He tested the components and completed the repairs.

I had a repairman here and after spending 350 dollars after 4 visits and parts, I decided to try it myself. I ordered a compressor start relay and a run capacitor. Replacement took all of 15 minutes and now runs again for the first time in a month. Thank you Parts Select. You’re the best!

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

the repair was so easy to do. it did take 2 of us to handle the door removal and reinstallation. we watched the video and carefully removed the door and had no trouble at all with the new parts installation. we knew what to expect and successfully fixed the frig! Good Deal!! Easy fix!!

Ordered new ribbon cable. At first I couldn't figure out how to get the wide end of the ribbon cable off, and I took the whole inner circuit board out - in fact, all it needed was more muscle, a straight pull out, no clips or anything holding it in other than friction. The narrow end attached to the control button board has two clips which pull towards you to loosen the ribbon. Easy install, worked perfectly

Easy to remove the auger Motor and Solenoid, however, it didn't fix the problem. $300.00 into it I now have to purchase a circuit board for $382.00. Not a happy camper.

Repair was easy. Unplug refrigerator, turn off water to ice maker, remove back panel, disconnect water inlet valve, disconnect water supplies and electrical connections. Cut ends off tubing to modify to new part connections, connect tubing, connect electrical supplies, reinstall back panel, plug refrigerator in, turn water supply back on. We made sure that there was no ice build up in the supply tube into the ice maker and made sure that everything worked correctly before putting it all back together. It was an easy repair.

Followed the online video from this site

Tested the start relay and capacitor with a multimeter and determined they were both bad (thank you, YouTube!). Ordered both here and they arrived in 4 days. It took me less than 15 minutes to install both; the appliance is working better than ever! The parts were very easy to access and replace.

Watched the video on your website and you can’t go wrong.
Thanks for being there
Mike

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!

I just removed the filter and then removed the filter housing. The housing is mounted using two screws. The only difficult part was removing the elbows from the water in and out lines. I don't believe the elbows are reusable. So I would go ahead and order new elbows when replacing this part.

Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.