10650452903 Kenmore Refrigerator - Instructions

1. Tried to unscrew the bolt that held the broken coupling.
2. Had to have daughter hold on the plastic spinner on the other side so that the bolt would unscrew and not make the whole mechanism spin.
3. Screw came out.
4. Put coupling in place.
5. Put screw back in and tightened everything up.
Really easy, once the screw actually began coming out.

PartSelect found and shipped the part quickly and with low postage directly to my door. I didn't have to worry about not being at home to accept the part and having to make a trip to the post office with a yellow slip.

It was so easy. I had no idea. My husband and I were directed to your site and we ordered the part with scepticism but with hope that it would solve the problem. As soon as it came in, my husband installed it in five minutes. It was working immediately. Thank you.

this site is invaluable - we searched and came upon it and the schematics for the model of fridge we have allowed us to identify exactly the part that we needed to replace. It was terrific - great site.

I used the computer to enter the make and model of the refrigerator with the icemaker unit. We looked at the diagram to identify the name of the part and then ordered it. It was sent out the next day! We received it and installed it and it works perfect!

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Super easy fix. Inserted shelf in to the shelf frame. Attached frame to refrigerator mounting bracket . Done in less than 5 minutes.

First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

First I had to figure out how to get the old unit out so I could work on it. The three screws that others wrote about were the ones that hold the motor in place. There are 3 screws holding the ice maker in the frame, along with one screw covering the electrical connection. The electrical connection was difficult to unplug because the locking tab was on the back side of the connection and with no room to work in the freezer it didn't become apparent until several frustrating minutes went by. There were no instructions provided, the picture on the ordering page showed the complete ice maker, and for $80 you get a printed circuit board with a small round item which must be the motor/timer control. The two plastic parts for moving the ice from the ice maker were included but not replaced because I didn't notice them until I had finished replacing the ice maker back in the freezer and wasn't going to start over again.
Once installed, there wasn't any noise, even of water flowing like the old one, could not tell if the unit was working or not. In the morning there was new ice in the bin indicating the repair had been successful. This is like anything else, if you have done it before it is a 5 minuter job but when you have to look at it and try to figure it out it takes a bit longer. All in all, it was simple enough, I was expecting a complete ice maker unit like was in the picture when ordered but only the motor module was actually needed.
We have another refrigerator/freezer that has an icemaker that is over 20 years old and has never been repaired, it is a Sears model though, probably made by Whirlpool or someone else.

I followed the video on this site. It was a pretty easy repair. Unplugged the fridge and turned off the water. Took off the bottom front panel. Used a nutdriver to remove the nuts holding the old filter housing in place. Unhooked the metal hook shown in the video. Disconnected the water from the old housing and removed it. The water line was a little short but I was able to reach in far enough to disconnect it without having to disconnect the line from the back of the fridge. Then I just reconnected everything to the new filter housing and installed a filter. Once I turned the water back on and plugged the fridge back in, it had better pressure than it ever has. Just watch the video and follow along.

Looked up on you tube to verify and see "secrets" to installation.

watched video on your website and followed directions

The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.

1st step is to watch the videos already available. Hands down... can't beat them.
Step 2 is copy what was done in the videos.
The only other piece of info I could suggest is when you remove the water line going to the filter housing from the solenoid valves is to tie/tape a piece of string onto it so you can find it when you reverse the procedure to put it back together. I am 70+ years old and do not bend in the middle, so the string would have been a great thing and would have lessened the frustration of trying to find the end of the tube.
Otherwise... happy sailing!