25344483701 Kenmore Refrigerator - Instructions

I unplugged the refrigerator and removed the back panel in the freezer. Here the coils were covered in a block of heavy frost. The coils needed to defrost, I allowed this to happen of the course of a few hours. Once this was done I used the wire cutters, cutting the two wires to the thermostat. Doing this I checked the continuity & got no reading. Having ordered the part at a more than reasonable price including 2 day delivery, I was ready to complete the repair. Stripping the thermostat wires connected the the freezer unit, I attached the two wires color to color to the new thermostat. Here I needed to insert both ends into the connector (butt end), crimping both sides. Making sure each end I'd secure. Do this for both sets of wires. Placing the new thermostat back on the the cooper coil (on the same one it was removed from), put the freezer back in place. Here I only screwed in two, in case I need to go back in. I plugged the refrigerator back in turn the settings back to default or factory. Allowed the refrigerator to come back up to temperature for 24-48 hours. I did these and I'm glad to say my 12 year refrigerator is working just like before.

I had to remove the face cover to gain access to the ribbon harness, also had to remove the push pads The ribbon is a delicate item so care had to be taken not to bend the ends. The ribbon can fit either side so getting it in place to make contact was kind of tricky. After the ribbon was in, it just a matter of putting things back together. Dispenser is fixed at a minimum cost, ribbon was shipped within 2 days which was great. Thanks to Part Select for easy to find on the net, had a complete diagram of the refrigerator ice/water dispenser so finding the parts needed was simple. Doug

The line for the water to the door was too short to install. Lacked about 4-6”Ice maker line was fine.

turn off ice maker, unplug electoral connection, under bottom of ice maker, remove two screws (hex) under bottom of ice maker, lift up on it to unhook it, take it out. (dump out all ice ). remove back plate on back of ice maker (two screws), the solenoid is held in place with two brass screws, remove them, then remove ground wire from solenoid and two wires, that connect to it,(make a note of how wires go back !). put it all back together and your good to go. . i dont think its really the solenoid that goes out, its the housing that encases it, and you have to buy another solenoid thats encased. good luck

I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure

Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.

Removed ice tray, disassembled ice tray assembly and crusher housing making sure to note the spring location, spring etc, installed new plastic housing making sure to reinstall the spring properly and the fixed crusher blade into the notch cutout., reassembled ice tray.

The door clunk problem was as others described. Repair similar to others described. The major thing to understand which I didn't see listed elsewhere is whether the top or bottom little nylon toothed cam is broken. This part is the one in the door. There was also one in the hinge, PS976594 or PS430814 ? I ordered this one and was lucky that it was correct. I'm not sure whether it's possible to know whether door side or hinge side is broken, without removing the door to see.

I just slipped it into place.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Repair man wanted a 130.00 service charge plus parts , With the help of YouTube we did the repairs inhouse , couldn't believe it was that easy. Refrigerator is working like a new one ,our maintenance crew has ice cubes were all happy !

removed water tray, used a razor blade to brake the seal from the face plate and the fridge, The hardest part was the three screws holding the dispenser face place on where rusted over. I wound up drilling them out. Once the screws removed, a slight lift, the face plate comes right off. I unplugged the cable, and set it aside. Now remove the next three screws, and the dispenser falls forward, (as far as the water line allows) undo the screws leaving the one emplace to hold the ice lever. push up twist. The hard part is getting the new one up and in. just takes a little patients.

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

Replaced bad parts with new parts it went easy

I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!