59665934703 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ricky from Philadelphia, PA
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
stop making ice
1.removed 3 nut screws-2 on top &1 on bottom.
2.unplug ref. from outlet.
3.unplug the wires from ice maker to ref.
4.remove ice maker
5.rinse new ice maker
6.plug ice maker to ref. using included wires
7.screw 2 top nut screws first then the bottom.
8.plug ref. back to outlet
9.made first ice in about 2-3 hours
2.unplug ref. from outlet.
3.unplug the wires from ice maker to ref.
4.remove ice maker
5.rinse new ice maker
6.plug ice maker to ref. using included wires
7.screw 2 top nut screws first then the bottom.
8.plug ref. back to outlet
9.made first ice in about 2-3 hours
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Woodridge, IL
- Parts Used:
- WP67001054
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawer glide broke
Removed the shelf, attached new glide, and replaced shelf
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Valley Grande, AL
- Parts Used:
- WP67005140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Appliance has Freezer on bottom and Someone dropped Item on handle a broke it
2 Screws on and off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dave from williamsville, NY
- Parts Used:
- WP67005140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
half of the freezer handle broke off
Not much to describe. Just used philips screwdriver and removed the two screws holding the handle in place. Discarded the broken handle, washed the area where the original handle was and replaced it with a brand new white handle (not yellowed with age)by replacing the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Annapolis, MD
- Parts Used:
- W10190935
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The icemaker in my freezer stopped producing ice
1. Removed the icemaker door
2. Removed the two screws from the underside of the icemaker unit
3. Removed the slide-on plastic cover that protects the power cable connector
4. Removed the icemaker unit
5. Removed the two screws from the control unit
6. Pulled the control unit from the icemaker unit
7. Installed the new control unit and reinstalled the icemaker assembly
A repairman wanted to charge me $250 to do what I did in about 20 minutes for about $120.
2. Removed the two screws from the underside of the icemaker unit
3. Removed the slide-on plastic cover that protects the power cable connector
4. Removed the icemaker unit
5. Removed the two screws from the control unit
6. Pulled the control unit from the icemaker unit
7. Installed the new control unit and reinstalled the icemaker assembly
A repairman wanted to charge me $250 to do what I did in about 20 minutes for about $120.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from San Diego, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker was leaking
This is an incredibly easy repair.
1) Remove the three screws holding the old icemaker
2) Disconnect the electrical connection (I used a spoon to get in and undo the connector clip
Do the opposite to install the new icemaker.
Total elapsed time was about 5 minutes.
1) Remove the three screws holding the old icemaker
2) Disconnect the electrical connection (I used a spoon to get in and undo the connector clip
Do the opposite to install the new icemaker.
Total elapsed time was about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lisa from sunrise, FL
- Parts Used:
- 67005125
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken freezer Handle
I just took the old one off and put the new one on..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EILEEN from TRUMANSBURG, NY
- Parts Used:
- WP67005141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer door handle was cracked
NEW SCREWS NOT INCLUDED with replacement handle! Removed old screws with a phillips screwdriver, cleaned them, reused screws to install new handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raoul from Thousand Oaks, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice maker not working
take out Ice maker tray, remove three screws holding the ice maker, unplug electrical connector. Replace with new Ice maker,Ice started to fill the tray. ENJOY!!
THANKS.
THANKS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Santa Clarita, CA
- Parts Used:
- W10190935
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker made no ice
After taking apart the ice maker, the only obvious replacement was the motor assembly. I check various Internet sites and found the best price at PartSelect.
I removed the ice maker from the freezer after turning off the ice make switch. Removal was easy with only one screw holding in the entire assembly. The ice maker has rails that allow it to slide in and out like a drawer.
After R/R the motor assembly and returning the ice make to the freezer all that remiand was to see if it worked.
Within 10 minutes I had the wonderful sound of water filling the ice maker tray. Within 30 minutes of that, ICE!!!
Shopping, ordering and shipping of the part was fast and efficient. I'll go with PartSelect for all my future appliance needs.
I removed the ice maker from the freezer after turning off the ice make switch. Removal was easy with only one screw holding in the entire assembly. The ice maker has rails that allow it to slide in and out like a drawer.
After R/R the motor assembly and returning the ice make to the freezer all that remiand was to see if it worked.
Within 10 minutes I had the wonderful sound of water filling the ice maker tray. Within 30 minutes of that, ICE!!!
Shopping, ordering and shipping of the part was fast and efficient. I'll go with PartSelect for all my future appliance needs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Galveston, IN
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker did not work
Took the old one out and plug the new one in, simply as 1 2 3. Order the part one morning,it was here the next afternoon, the ice maker was fixed in less than a half hour. we will order from you the next time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Clarkston, MI
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water dripping in ice cube holder
We removed three screws, unplugged the wire and then removed the old ice maker. Installed the new ice maker with the screws, plugged in the wire and shortly after that we had ice! I was nervous about this repair but it was so easy and the part was here in three days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Concord, MA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Would not make ice any longer
I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Long Valley, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Ice Maker didn't produce ice cubes.
It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Santa Maria, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice tray leaking
Super! It was so fast and easy to fix. Receive my kit in three days and save a lot of money not having to have a repairman come and do it!
Was this instruction helpful to you?
Thank you for voting!