10658032801 Kenmore Refrigerator - Instructions

Patience is a virtue. The kit really works. 1st, lift the front plate of the ice dispencer by placing a flat head screw driver into the two slots at the bottom of the panel. When the panel is lifted up slightly at the bottom, push up on the panel to remove it. Careful not to break panel and the wires attached. Next, remove the wiring panel by removing the two screws on left and right sides. Then, unplug the old black ice cover from the wiring panel (this is the heating plug that you will nolonger need). Next, remove the parts and replace them with the parts in the kit, noting where each part comes from, etc. All parts in the kit are necessary and should be used. Some of the replacements need trial and error. Patience will be important. Also needed is a person that loves to solve problems, especially because the kit does not come with instructions. But the kit definitely works!

unplugged fridge, turned off water supply, disconnected water supply line (towel to catch drainage). remove cardboard lower panel from back of fridge. remove 2 bolts holding existing water inlet valve assy to fridge. Disconnect 2 electric plugs from assy. water lines disconnect using push/pull method (mark where they go). If any water tube line has any surface imperfections trim off a small length of line using a razor knife (cut tubing perpendicular (or "square" )on the end. I had to remove small unused part from the new water inlet valve assy. Insert the 3 water lines to the correct spots: push them on,fully, give a tug to make sure they are connected fully. Reattach the 2 electrical plugs.Bolt the unit back in place. I connected the water & plugged it in, filled about 10 glasses of water and made sure an ice cycle ran, to check for leaks (none found). I cleaned off some of the dust on the back of the fridge, reattached the cardboard lower piece. and listened to the sweet sound of Ice filling, and not my wallet emptying to the service man!!

It was ridiculously easy. Push the button on the filter canister holder at the base of the refrigerator and the spring-loaded mechanism came out smoothly. I unplugged the old filter, took the cap off the new on and plugged it in. After reinserting the filter canister holder and locking it in place, I heard the whoosh of water once again moving through the filter. Very satisfying and very easy to do.

First checked to make sure the water reserve line inside fridge wasn't frozen (soaked coil at back of fridge in a container of warm water for 10 min). That seemed fine and icemaker was still working so assumed that portion of the water inlet valve feeding water line wasn't working. Video on PartSelect website showing how to replace the valve was spot on and gave me confidence to install myself. Part arrived within two days and installation was done in a snap exactly as shown in video. All the lines & wire harnesses fit perfectly, water & ice working great, and I couldn't be more pleased.

The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and start the process of putting back together the opposite way you took it apart.

Purchased new motor from Partselect.com. When it arrived it came with a new rubber washer that fitted on top of new motor that was not on old motor, that how water got into old motor. However, the instruction sheet did not give info on how to access the proper way to the motor that is the door. Not wanting to damage the freezer door assy. called in a tech who made it look easy, but even he had a little problem locating access panel that was directly under the motor in the freezer side of the door. After that it was a piece of cake.

Remove the front panel strip where the temperature adjustment lights show, use a thin screw driver to pot the strip out along the top. Use a nut driver to remove the control panel which contains the light, two bolts on the under side, two bolts on the front after the panel strip was removed. The control panel will hang down enough with the wires attached to allow access to the thermostat. Use a Phillips screw driver to remove the side cover where the temperature probe runs along the left hand side to the unit, one screw. You will find the temperature probe inside plastic tubing running to the back of the unit where it is wrapped around a Styrofoam holder with three plastic retainer clips on the top and bottom. Unplug the thermostat from its electrical connection. You may want to unplug the unit’s wall plus as this is 110 volt connection. Remove the two screws holding the thermostat to the plastic control panel; remove the fiber optic connection to the light strip that runs across the top of the thermostat. Remove the temperature probe from the 6 clips and pull the entire unit out. Remove the plastic tube from the old temperature probe and slide it over the probe from the new thermostat. The probe is approximately 26 inches long and you must take care not to crimp it as you slide it in the plastic tubing(warm the plastic tube with a hair dryer to reduce stiffness at the bend). Plug the wires into the new thermostat and reassemble.

I first removed the power cord of the refrigerator from the receptacle. I then removed the screws (3 each) from both the emitter and receiver face plates with a phillips screw driver. I than carefully removed the connector to the each of the circuit boards. A simple pull maneuver. I removed the circuit boards from the face plates. I took the new parts and put them back in reverse order. I put the power cord back in the receptacle.

Removed the filter and put the cap on the new filter and inserted it as instructed on the filter box. Really easy now that we have the new cap.

I removed the cardboard backer board at the bottom rear of the refrigerator. I had to remove two screws to free the old inlet valve from the frame. The old water tube fittings were compression (screw on) type, so I cut the ends off cleanly with a sharp blade. They inserted into the valve holes easily - just needed a good push to lock them in solidly. The tubes are different sizes, so it was easy to know which one goes in which hole - the electric connectors were easy to transfer from old to new... screwed the new valve back onto the frame, re-installed the cardboard backer, flushed the system -- and no more leaks!!

I had read on a fix it site that the start device for the compressor on this particular model was known to fail after 3-5 years. When we received the part it looked like something that just plugged into the compressor. My husband unscrewed the panel in the back of the fridge and saw the part on the compressor. He first removed the three wires that it was connected to, and the wires were inside a plug so all he had to do was remove the plug from the start device. He then removed the old start device from the compressor. Plugged in the wire plug into the new start device, and pushed in the new start device into the compressor. There was also another black part plugged into the old start device that he plugged inot the new start device that connected to the compressor. Our freezer and refrigerator starting working. Within a couple of hours our freezer had made ice.

Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'

First I removed the old lightbulb from the socket and replaced it with a new one to confirm that the bulb was not the problem. I then pryed the socket out with a flat-head screwdriver. I could tell that the socket was anchored in its hole with clips so it was relatively easy to pry it out. Once the socket was out, I disconnected the lead wires and ordered a replacement socket kit from Partselect. When the new one arrived, I reconnected the lead wires to it, snapped it back into its hole, screwed in a new lightbulb, and presto!! The light was back on with no further problem. Thank you, Partselect!! A $15.00 part saved me what probably would have been at least a $100. service call and heaven knows what the technician would have told me I needed!!!

Removed all items from frig,put it on its back side,removed metal cover and removed housing screws,hoses.

It turn one turn on the filter holder, pull out and put new filter in done