59677539702 Kenmore Refrigerator - Instructions

I replaced both side. The left side I very easy to replace. It has 2 screws holding the end cap in place and the tracking has 2 screws holding it in. Undo the 4 screws and put the track on the new end cap and then you are good to go to install the new end cap on the left side. Now for the right side is easy, but you now have to also undo 2 screws and other 2 for the track just like left side but also you are going to have to undo the humidity control stuff and put it on the new end cap.

The broken one just popped out and the new one popped right in! This company shipped out the part I needed immediately I had it in two days!! I highly recommend them!!

Really easy once I figured out which way the rail went in.

I used the repair as an excuse to clean the refrigerator!!

Part was pretty ubiquitous so plastic door pins part fits a lot of refrigs, no tools necessary, new part is flexible enough to bend slightly to fit over pins at side. Mine was a bottom freezer type.

Really easy - Remove drawers, remove glass shelf and associated support rails, remove drawer slide from old endcap, remove old endcap, reverse proceedure installing new endcap - now the hard part, have a cool softdrink while you carry the old endcap and packing material from the new one out to the trash.

By the way - the part got here really fast - thanks for the great service.

took out the drawers and glass shelf and unscrewed the sides took parts for drawer glide off put them on the new part reinstallled saved $110 service cll and $20 on the part!

Followed Youtube video from Free Repair Help. Only problem was getting down low enough to see the pins on the Compressor to plug the replacement Compressor Start Device and Capacitor-could not replace the old clip to hold the unit to the Compressor like the old unit had. At 77 I just have a problem bending over.

Removing the old pieces & figuring out how to separate the front trim so it could be reinstalled on the new frame took the longest! (released the securing tabs with a screw driver). Reinstalling the new parts were straight forward, "no problem". (epg)

followed instructions and used common sense and the salesman was very helpful and knowledgeable and he contributed a lot of help in finding the right parts that fit

took out old lid, took out drawers above this drawer to make it easier to work on. installed new drawer simple by hand with no tools. put other drawers back. very simple no tools needed.

Two phillips head screws out to remove drawer slide. Three screws to remove right side drawer support. New support placed, new lid snapped into place. The right side has an adjustment lever. Re-routing that took the longest. The arm had to be removed and twisted to get the adjustment knob off and on.

I ordered the part and it arrived in about 5 days. I removed the two lower crisper drawers and the glass shelf seperating these from the Wide-N-Fresh compartment, to give me room to work. I removed the two screws holding the right side endcap in place. The temperature adjustment mechanism was a bit tricky to remove from the broken endcap and replacing it on the new endcap. Once that was figured out everything fell into place and the lid was snapped into place and worked properly

this pantry lid was warped when the fridge was new. tolerated it for a while finally it cracked then worked pretty well for a couple years until the RH hinge pin (part of a support for the pantry door)broke. I had never bought parts from partselect.com before, but I have in the past bought repair parts from other sites. Partselect.com had drawings of the refrigerator parts that although were a little hard to see were adequate to tell what parts I should order. I ordered the parts, they came in after an acceptable wait. The parts were literally perfect, went right in, and everything is working quite nicely. I am happy with Partselect.com and will probbly go to them first in the future. I actually like the refrigerator a little more now than I did when it was new.

Receive part in two days. Super fast.
Repair was very easy. Whirlpool designs so even the "average joe" can fix it. Took abour 20 minutes to repair. Even with no directions.

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years