10664263402 Kenmore Refrigerator - Instructions

My tenants moved out of my rental property and abandoned their refrigerator there. The freezer door would not close properly because someone had previously removed the lower door support bracket and failed to replace the lower bracket shim that positions the lower part of the freezer door properly out from the refrigerator cabinet causing the door gasket seal to bind before the freezer door was fully closed. I removed and replaced this lower door bracket with a new shim made up of serveral thicknesses of cardboard to achieve this spacing and freezer door now closes and seals properly. They had never connected a water supply to the refrigerator although this model is equiped with an ice maker and in door ice and cold water dispenser. The access panel on the back of the unit had been previously removed and discarded. I made up a new access panel from cardboard and connected the water line to the solenoid valve. Valve was so old it would barely open when valve energized and water flow was too slow to make proper sized ice cubes and fill a water glass. I purchased a new water solenoid valve and replaced ther original valve and cured that problem. Replacing the access panel cured an improper cooling problem because with panel removed, most of the air flow bypasses the condenser coils. Lastly I replaced the upper tubular light bulb and the lower light socket I purchased here and installed a 40 watt bulb in the new light socket. Presto! I was able to turn non working abandoned refrigerator into a workable unit.

Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.

Took out the cracked one, and replace with the new one. Fitted perfectly.

I ordered the drawer which arrived 3 days later and I just took out the old one removed the white handle cover placed it on the new drawer and put it back in quick, easy done.

Just slid the drawer into the runners and finished.

Replaced drawers.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

This was a simple install. I just replaced the glass shelf on the sliding shelf bracket.

Open your door as far as it will go. Line it up with the plastic holder should just slide into place.

Replaced the drawer

I was prepared for the part not to fit because it's a 23-year-old fridge, but it fit perfectly, no issues whatsoever. I plan to buy a crisper drawer as well. Glad I found this vendor.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Took the glass shelf out of the fridge in our rental home to clean and it just shattered in our hands. Did a search online and found part select, phoned to make sure I was looking at the correct part, the lady on the phone was very helpful. I ordered the shelf using the next day service as we were returning home to the UK within 3 days so did not want to take the chance of not receiving it before we left. I got the notification the part had been dispatched, the part was delivered early next morning. Took the shelf out the package and placed in the tray, job done!. Great service will definately use again, have book marked the site.

Ordered the new part, it was the perfect size and slipped right on to the existing brackets.