25367173506 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DANIEL from CAPE CORAL, FL
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
FREEZER COMPARTMENT NOT COLD ENOUGH (20 DEGREES)
REPLACED TIMER-DEFROST 215846602..REPLACED THERMOSTAT-DEFROST KIT 5303918202..REPLACED CONTROL, TEMPERATURE 5304421256..RECHARGED SYSTEM WITH 134A...ALL FANS WORKING...COMPRESSOR RUNS.. FREEZER STILL NOT GETTING COLD ENOUGH...HOLDING AT 20 DEGREES...ANY SUGGESTIONS..THANKS..DAN
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aaron from ODESSA, TX
- Parts Used:
- 5303918549, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Fridge was't cool
I just followed the instructions on the videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from NEWHALL, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Evap fan motor comes on and off will not stay running
pulled back panel to get at evap fan motor cut wires to remove reinstalled hooked up wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald from WEST PALM BCH, FL
- Parts Used:
- 5303918549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Noise from fan
I watch the video on your site and this make iit very easy to do. That repair that tooks me 40 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from BERKSHIRE, NY
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Freezer worked, no fridge
Removed panel over the motor in the freezer department. Removed screws holding the motor in, unplug wires. Reversed process to install motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SOUTH HAVEN, MN
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Fan motor in the freezer was not working. The freezer was still cool enough to keep the food froozen, but the refrigerator was not keeping the food cool and the liquids were getting warmer than normal.
Very easy process. Watch the YouTube video, it goes step by step for the repair. The part was $33, shipping was $6. Take your time and fix it yourself or pay $500 for a new refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earnest from BOWDON, GA
- Parts Used:
- 241872512
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket was damaged everything inside would freeze
Pulled the old gasket out and pushed the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CHICOPEE, MA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
None fit perfectly
Just slid it down into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from N LAS VEGAS, NV
- Parts Used:
- 240350609
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The glass shelf broke above the 2 drawers on the bottom
Just lay the new glass shelf into the groves. The shelf was too big and would not fit properly down into the groves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from LEXINGTON, KY
- Parts Used:
- 240358928
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The plastic frame around the shelf broke!
Only thing we needed to do was to slide in the glass shelf into the grooves inside the refrigerator!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Okeechobee, FL
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Intermittent loud noise coming from fan motor located in freezer compartment
Ordered a new evaporator fan motor and watched the repair video supplied by part select on their web site.It was spot on step by step instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Hayes, VA
- Parts Used:
- 241872512
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket failed
Simple. Just pull old gasket free from door. Pace new gasket on door and ensure that gasket is seated in the gasket channel all the way around door. This part fit door properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SHERRY from LAUREL, DE
- Parts Used:
- 241872512
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
No problem
It was so easy to install it. I did great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from STOCKTON, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator wasn't getting cold
removed the back panel of the freezer and unplugged the connector for the Motor. Removed the air diffuser, then removed the fan blade. Removed the 2 screws holding the motor to the bracket. Disconnected the old wire harness and installed the new one. Put the fan blade onto the new motor and installed the motor onto the bracket. Put the air diffuser back on, plugged the motor back in and fastened the back panel. Plugged the refrigerator into the outlet and tested, OK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MONTGOMERY, IL
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Coils frozen over. Refrigerator not cooling
I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!