25357103608 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Denise from Lowell, MI
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
just quit working
Bought a new
capacitor.
capacitor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Roanoke, VA
- Parts Used:
- 5303918774
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Replaced the heater-core motor
It was fairly easy. Only had to remove the back cardboard. Remove 3 screws and the power plug.
Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.
Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.
Was this instruction helpful to you?
Thank you for voting!
Had a broken door bin and shelf support stud
I pulled out the old support stud with a pair of pliers, pushed the new stud in, and gave it a few taps with the hammer to secure it in the fridge wall. For the door bin I just slid the new bin in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Anderson, IN
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
drip from door water dispenser
The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Buffalo Grove, IL
- Parts Used:
- 5303918214
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Freezer was cold but the fridge was warm. Back panel of fridge was building up frost
First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .
The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.
The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from LAURENS, SC
- Parts Used:
- 241600906
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Not cooling
Just took out 4-5 screws and follow the instructions and repair went great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from ORANGE, TX
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker quit working
Followed the steps in the video on your site, really easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Bristol, IN
- Parts Used:
- 240524102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broken Fan Blade
Pull refrigerator away from wall, being careful not to kink or break water line to ice maker, unplug refrigerator. Using 1/4" nutdriver, remove cardboard lower rear panel, bottom lifts out. Fan and motor are now directly in front of you, grasp the moter to stablize it, and using your other hand, pull fan hub from motor shaft. Be sure motor shaft is clean before reinstalling new fan blade, press new bladr onto motor shaft, until center of blade is centered on outlet side of fan housing. spin blade by hand to insure clearance. Plug refrigerator in and observe operation of fan, refrigerator needs to be calling for cooling for this fan to operate. Reinstall cardboard panel and move refrigerator back into position.
Was this instruction helpful to you?
Thank you for voting!
The door had a loud popping noise everytime you opened it.
The biggest part of the repair was getting everything out of the shelves in the door. I had to remove one phillips head screw from the plastic hinge cover on the top of the appliance. As per the owners manual I traced around the hinge with a pencil so I would be able to align the door to the same postion. Removed two screws with a nut driver and removed the top hinge. The magnetic strip held the door in place until I grabbed it and pulled it open then lifted it up off of the bottom hinge. I layed the door on the island counter and pried the bearing hinge out of the door stop and replaced it with the new one. I probably could have stopped there but figured the plate might have been worn so I remove one phillips head screw from the bottom hinge, lifted the plate off, and replaced it with the new one. I assembled everything in reverse order and voila, no more popping noises.
Was this instruction helpful to you?
Thank you for voting!
Hinge bearing broke causing door to rub when opened
I removed the screw in the plastic cover on the top of the fridge that covered the fridge side hinge first. Then, I removed the two nuts with a nut driver that hold the hinge in place. After removing the two nuts and the hinge, I lifted the door up and out of the bottom hinge and placed it on a flat surface. I used a pair of pliers next to pull out the broken hinge bearing from the bottom of the door itself. After removing the old bearing I inserted the new bearing in the door. Next, I put the door back on making sure the hinge went into the hinge bearing and put the door in the closed position. After that was all done and the door was set properly, I put the top hinge back on with the two screws and put the plastic cover back in place. Took 20min to complete. A second set of hands would have been helpful with putting the door back on, but it can be done by yourself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Herington, KS
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
It Was Fast And Easy, No To Mention Affordable.
Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEORGE from ASHEVILLE, NC
- Parts Used:
- 241993001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Crisper Supports broken
Removed supports with pliers and used center punch to push broken plugs out of hole and inserted the new supports.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Belton, TX
- Parts Used:
- 5303918344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker over flowed
The ice maker would over floew then not cycle it would freeze with the forks stuck in the ice! so just get your modle # and serl, # call in and order the hole ice maker it cost only about $120.00 with shipping!! it is so simple to put in just lossen the 2 1/4 screws in the back and lift up then unplug it. you do not have to turn the water off as it works off the pump at the bottem !!( note you nedd to take the ice bucket out it just slides right out !! You will save the service call from A repair man it is really very easy so by the time it took to read this you will have it done !really its that easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from BRONX, NY
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
evaporator coil would freeze up solid. no air flow through coil; no cooling.
-unplug power cord.(safety first!
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from New Orleans, LA
- Parts Used:
- 241885001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Original gate broke at the swivel point
I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!
This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.
This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.
Was this instruction helpful to you?
Thank you for voting!