59678282902 Kenmore Refrigerator - Instructions

Remove cover inside frig at rearwall top with screw driver. Remove phillips screws holding unit in place. Unclip connectors ,and replace in reverse order.

Inside the food section above the top shelf behind the light in the back, remove the lid from the cover in lifting from the lower edge no tools necessary here. Remove two screws with Phillips screw driver remove entire housing inclusive Styrofoam insert. Unplug damper Control Unit. Remove two screws and remove damper control unit and replace in reverse order. Finally that refrigerator is quiet, I should have done this long time ago. Unbelievable this is the second part I have to replace on this expensive refrigerator.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Popped out old gasket and popped in nwe one. This is where things get interersting, the new gasket
Does work as well as the one I replaced. I think the maganet is not strong enough. If anyone has had the same problem please let me know. This model ( Maytag- French door ) has been a lemon.

Took drawers out, inserted the rail and put the drawers back in and voila. Fixed.

Watched Partselect video of P-trap installation.Removed water line & back cover& disconnected wires to water solenoid .Removed old drain tube & old problematic rubber funnel. Used contact cleaner to clean rubber residue from drain line and used a little silicone to aide reassembly. Job went well thanks to video.

changed the starter connected to the compressor

took the pantry drawer out removed track replaced and put on new door... very simple

Simply move the appliance for access to the back side. Removed the lower metal access panel, locate the compressor ( black round object ) parts are on the left bottom of the compressor. Simply unplug the parts, and replace with new parts.The hard part was, getting my 72 year old body in position to do the job. As far as getting the right part, a young lady in Nova Scoita is the one to ask for help !! Ordered parts one day, and they were in my hands the next morning!!

Took the new door seal out of the box, layed it out as straight as possible heated it with hair dryer 4 1hour took the old 1 out by hand and replaced it with new one no tools needed 10 min job

I was easily able to find the part using the online search. I order the part and it arrived in about two days. Installing the part meant pulling out the two crisper drawers, emptying the shelf above the crispers, removing two glass shelf plates, inserting the new part, replacing the glass plates, replacing the food on the shelf and sliding in the two crisper drawers. All in all, about 3 minutes.

1. Empty your fridge. Lighter is easier to move and this is the hardest step in the fix. 2. Move your fridge so you can get behind it. Unplug the fridge. 3. Use a 1/4in nut driver to remove the screws from the back panel. 4. Remove the back panel. 5. Locate the compressor (big cylinder, usually black) and find the capacitor (PS11757023) and start dev (PS11750123) plugged into the side of the compressor. 6. There is a steel spring restraint wire, remove this. 7. Remove the pin connector (plastic w/ wires going to it) by pressing and pulling gently. Remove the old capacitor and start dev. 8. Assemble the new capacitor and start dev to each other. 9. Plug the pin connector into the new replacement components. 10. Align the start dev to the location of the old components. There is a 3 pin outlet that aligns to the 3 plug holes on the start dev. Align the plug then push gently but firmly to seat the components back together. 11. Reinstall the restraint wire. 12. Reinstall the pack panel. 13. Put your refrigerator back in place and load it up! You're all done!

Removed door from slide bars with small nutdriver, pulled old gasket out of retaining slot, cleaned slot & area around it, pressed new gasket into place with fingers, relatively easy. Used hair dryer to make sure gasket was formed properly and contacted fridge unit eavenly.

replaced broked crisper pan with new pan

To keep from having to pay the appliance repairman $100.00 for a diagnostic fee I just started replacing parts that were known for causing this problem. First I replaced the compressor switch and capacitor that didn't work so then I replaced the damper controller then I replaced the control board then I saw that the evaporator fan wasn't spinning so I replaced the evaporator fan motor and the bimetal defrost thermostat. That was the problem I wish I would have checked that first. But it works like new now.