25361789011 Kenmore Refrigerator - Instructions

This was the second part I tried. The defrost timer was first, but that did not fix it. To do this I had to remove the ice maker and the back plate of the freezer. Then I defrosted the coil and cut the wires. stripped them back and installed the new thermostat. re-assembled and tested. has been working great ever since.

I unplugged the refrigerator, then opened the door and removed four screws holding the plastic electrical panel to the interior top of the main refrigerator compartment and noticed the cold control was corroded badly, apparently from moisture in the panel. I ordered a new one from partselect.com. When it arrived the next day, I then pulled off the control knob, unclipped the cold control, unplugged the three wires to the control, then removed the styrofoam insulation blocks holding the thermocouple wire and then removed the thermocouple wire to complete the removal. I then reversed the process to install the new thermostat and control. That is repositioned the thermocouple wire, put the insulation blocks back to hold the wire, then replugged the three electrical wires, clipped the control back and pushed the control knob back on and finally screwed the panel back to the top of the main compartment and plugged the refrigerator electrical cord back in to provide current to the refrigerator. It immediately started up and ran fine. Total time - about 8 minutes.

Took whole shelf out. Unscrewed the old rail, screwed in the new rail. Female 55yrs old. I broke it myself and fixed it myself! Very easy!!!!

removed the screws in the piece of the rail that was still attached and replace with new one - hardest part was the screw it was so little I started it without the magnetic screw driver - it took about 20 minutes

I popped the new one in. My cat could have done it

Bought a new
capacitor.

All I did was to take out the cracked pan and slide in the new one.Excellent service.I ordered the pan late evening one day the part arrrived not the next day but the day after.I expected that it would have taken a week or better.I recommend Part Select.com because of this.

This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

Pull out the shelf and remove the one screw that holds the support rail in place. Remove broken rail, slip in the new one, then replace the screw. Done!

It takes longer to remove items from shelf and clean it than it does to replace the part.

I unscrewed the old rails and took the number to order on the first day. The order came on the 3rd day. Can you imagine such fast service.
My daughter is a single mom with 4 children, one of whom was responsible for the breakage. I am the grandmother and was very grateful for the fast service and great price. The drawer was installed in 10 minutes. I just screwed the old screw into the new part and replaced the drawer. Thanks

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.

Went pretty straight forward, except the heat shrink tubing was about 2 sizes too big. Would not shrink small enough to seal the connections. Even with a heat gun it would not shrink small enough. OH, another think is when I plugged the fridge back in the defrost timer was in defrost mode. Took me a few minutes to figure that out and use a screwdriver to turn the timer back to the on position. Other than that, install was pretty simple.

I removed the shelf that hold's the rail's then one (1) screw that hold's the rail in place then I replaced the shelf. Simple & Easy!!

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Took out the broken piece, replaced it with the new support using only a screwdriver, and VOILA, it was finished. Thanks!