2535462240A Kenmore Refrigerator - Instructions

One of the bins on my freezer door had the tabs, that hold it on the door, broken off. I orginally ordered the wrong item, but I called right away and Parts Select had the correct item to me immediately. It was a very easy fix, I just had to snap the bin in place once it arrived.I am very impressed with PartSelect and their service. I would definately use them again and recommend them to others.

Removed stuff on door, removed 2 screws on top of door, lifted door off replaced one door closure/hinge bearing and one door closing plate and put door back on and wala no more thump.

Went the typical route of part replacement since I don't own an ohm meter...pull and replace one part at a time. Started with the cheaper parts first, replaced the freezer fan for $40, same problem. Replaced the defrost heater element for $40, same problem. Replaced the thermostat $15 and controller board $150 at same time, bingo problem solved. Had to defrost with the hair dryer each time, biggest pain. Had an issue finding a Utube that showed the water filter system and thermistor removal for this model, otherwise straightforward, but not a 30 minute job.

First I removed the door. Took off the broken parts and replaced them. Easy and fast to repair.

Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.

The new bin arrived, I slid it in place and away we went.

I ordered 3 items based on my model and serial number from the website.

First I removed two screws per rail and removed the old rails. I replaced with the new rails and used a nutdriver to secure in place. This was extremely easy and I fell like my fridge is brand new again.
You can do it!!!

No problem, I Just pushed the plastic pin to the old support studs into the frig wall using a small screw driver and hammer and with pliers pulled the studs out to the wall of the frig being careful not to damage the wall. Then with pliers {needle nose} pulled the plastic pin out of the wall. Pushed the new support studs in the hole and tapped the plastic pin with a small hammer into the support stud. Replaced crisper drawer cover and glass shelf. Easy fix

I recieved the part within 48 hours. I snapped the part in place and I was done in seconds.

Parts Supply had a YouTube video to show it was done. This is one of the best sites to get parts there is. Easy to use, tells you how to install them easily. Thanks Parts Supply, I'll be back whenever I need a appliance part.

I replaced the water valve, but it still did not fix the problem.The old water valve I took out I'm assuming worked fine, I think the real problem is ice building up in pipe or some other blockage.

Parts select was very fast in shipping, very positive experience with them.
I will definitely purchase again from this site.

I followed step by step instruction in the hinge kit; Replacing the old hinge with a new hinge and two new plastic cams in the kit. The kit hinge has an adjustment to level the right door with the left door. Everything is done in 20 minutes for a senior guy like me. Very easy.

removed ice maker box and disassembled crusher unit on front of box and installed new housing.

Pull refrigerator from wall and disconnect the water line and unplug the power.

On top of the icemaker, two machine screws hold the icemaker to the side of the refrigerator. You will have to feel around to find the machine screws, but once you do, it is simple to slip the appropriate size socket over the hex heads. I found it helpful to have an extension on the socket wrench. Disconnect the power cable inside the refrigerator (there are little pressure clips on the side that help release the cable) and move it out of the way for the time-being.

Back out both machine screws several turns, but do not remove them completely. The icemaker slips over the screws, so leaving them in the side of the refrigerator makes that process a lot easier. Hand tighten the machine screws once you have positioned the new icemaker in place. One thing to be sure and do is make sure the water line hose coming out of the back of the refrigerator inside is on top of the icemaker. It fits into a slot in the top of the icemaker - failing to do this will result in water pouring into the freezer compartment, not into the icemaker..

Reconnect the power cable to the new icemaker and tuck it up behind the icemaker assembly. Tighten the machine screws completely, but do not over-tighten.

Reconnect the water line on the back of the refrigerator at the wall, and plug in the refrigerator. You should hear the unit fill immediately.

In about an hour you should have ice filling the bin. Enjoy!