10651189110 Kenmore Refrigerator - Instructions

Removed the broken coupling with the new one from your store. It took less than 10 minutes. The video you provided on the website was very helpful.

Simply move the appliance for access to the back side. Removed the lower metal access panel, locate the compressor ( black round object ) parts are on the left bottom of the compressor. Simply unplug the parts, and replace with new parts.The hard part was, getting my 72 year old body in position to do the job. As far as getting the right part, a young lady in Nova Scoita is the one to ask for help !! Ordered parts one day, and they were in my hands the next morning!!

Unplugged and empty refrigerator, completely defrosted refrigerator using a hair dryer to speed up the defrosting, put a lot of towels on the floor to soak up the water when the ice melts. Removed all refrigerator racks and drawers, then remove the white plastic and styrofoam condenser cover. You will then see the thermistor, cut the two small wires connecting the thermistor to the harness leave yourself as mush wire as possible. Splice in the new thermistor and put the refrigerator back together.

First I installed a defrost timer, (the old timer had burnt out contacts in it) It seemed to work for a few days, then went back to not comng out of defrost cycle, I then installed a defrost thermostat. It seems to be working better than before. I found out that maybe I wasn't running it cold enough. So I turned it up colder. Now it works ok for 2 - 3 days, then I check the Temp in the freezer and its up to 6o. So I manually reset the timer and it works for 2 - 3 days. Don't know what to do now to fix it.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!

First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.

This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.

1. Empty your fridge. Lighter is easier to move and this is the hardest step in the fix. 2. Move your fridge so you can get behind it. Unplug the fridge. 3. Use a 1/4in nut driver to remove the screws from the back panel. 4. Remove the back panel. 5. Locate the compressor (big cylinder, usually black) and find the capacitor (PS11757023) and start dev (PS11750123) plugged into the side of the compressor. 6. There is a steel spring restraint wire, remove this. 7. Remove the pin connector (plastic w/ wires going to it) by pressing and pulling gently. Remove the old capacitor and start dev. 8. Assemble the new capacitor and start dev to each other. 9. Plug the pin connector into the new replacement components. 10. Align the start dev to the location of the old components. There is a 3 pin outlet that aligns to the 3 plug holes on the start dev. Align the plug then push gently but firmly to seat the components back together. 11. Reinstall the restraint wire. 12. Reinstall the pack panel. 13. Put your refrigerator back in place and load it up! You're all done!

Removing the panels inside the freezer section was the most difficult ,because it is narrow,hard to fit your body inside compartment, in order to cut wires and to splice Bi-metal Defrost Thermostat wires (2 ) Watch the videos on the web site so you know where to start. First time I ever "repaired " a large appliance, saved me over $ 600.00 (that's what the people I bought the Refrigerator from wanted to charge me.) My parts cost 65.00 !!!!! My younger brother turned me onto the web site... , I'll be returning to the site and telling my friends about it. It's a total "rip off" what service organizations charge the general public these days from Car Dealer ships to the stores we purchase our appliances from. !!! Glad I still have my health and faculties to repair the essentials we have around our homes. !!!!

Remove ice maker from freezer, place on its side on table. Remove single screw securing coupling from shaft without removing shaft from housing. Remove old coupling, and attach new coupling using single screw.

This is a great time to completely clean the Ice maker bin and crusher unit.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

I followed your instructions , the only thing that was left out was that the freezer has a drain hole that had to be thawed out with a hair dryer,till the water went to the drain pan underneath the ref. your instruction were through enough, that's why I purchased the part from your company, I installed the part 2 days ago and its working like new again 23.00 for the part instead of 1200.00 dollars for another ref. thanks very much. 6 months ago I purchased the relay and compressor starter from your company at that time per your instructions I shook the compressor starter and like a light bulb it had something broke inside,I needed that thanks again oomk

Contacted sears home service to perform repair. Quote for repair was $307. 43. ( $196. 90 For labor ,$102. 58 For part) plus $75. 00 For service call. Based on the charge, I refused the repair and ordered the appropriate part from "part select" (733947) (wpl 8201515) motor module for a cost of $81. 84. To my surprise, the part arrived the next day and in 15 minutes the icemaker was in a position to make ice, and has been producing ice ever since. To perform the module replacement, I had to remove one screw with a nutdriver, pull the icemaker out, disconnect a wire harness, replace the module and do the reverse procedure to complete the installation. I saved a total of $225. 59 By doing this repair myself. A lesson learned. . . . . I will always investigate doing a repair myself with the help from the people at part select. Very professional and they sent the correct part the first time.

Not being a professional repair tech, I looked at this sites provided schematics of the ice-maker. I assumed due to the problem I had which parts to order. the parts arrived within 3 days and after I took the icemaker apart I quickly realized I ordered the wrong parts. I called and asked what to do. since I did not open the packaging for the "wrong" parts I was able to make a return. I then called back because I discoverd the part I really needed wasn't shown in the sketch. I was told that I needed to order a new motor and it would have the part I needed. I ordered the part and within 3 days it arrived. Once I had the new part I was able to quickly install. Now I have a icemaker that works better than new since ,now it does not seem to jam either.

To make the repair:
First remove the 1/4" nut head screw on the under side of the ice maker.
Remove the shroud covering the electrical connection.
Slide out the maker and depress the locking clip.
Disconect the electrical wires.
Pull off the motor cover (no screws).
Remove the three philips head screws from the motor housing. Gently remove the motor.
Next loosen the screws and pull the "black motor-mounting harness" untill enough clearance to remove the ejector arm and deflector tray. The new kit will have a new ejector arm and deflector tray.
Insallation is the reverse.
The schematics were very helpfull.
It was very simple and I saved a $150 service fee to have someone else do it for me.
PS. When I called I was able to speak to real live Americans who were able to help me, were pleasant, polite, and professional, AND they did not treat me like I was stupid because I am not a professional repair man. I will definately use this service again. and recommend to all my DIY friends!!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you