10677224700 Kenmore Refrigerator - Instructions

This is an incredibly easy repair.

1) Remove the three screws holding the old icemaker

2) Disconnect the electrical connection (I used a spoon to get in and undo the connector clip

Do the opposite to install the new icemaker.

Total elapsed time was about 5 minutes.

1. Removed the icemaker door
2. Removed the two screws from the underside of the icemaker unit
3. Removed the slide-on plastic cover that protects the power cable connector
4. Removed the icemaker unit
5. Removed the two screws from the control unit
6. Pulled the control unit from the icemaker unit
7. Installed the new control unit and reinstalled the icemaker assembly

A repairman wanted to charge me $250 to do what I did in about 20 minutes for about $120.

1). Pull Frig away from wall,
2). Unplug Frig
3). Turn off water feed
4). Remove cardboard dust shield on lower back
of frig (1/4" screws. I used socket)
5.) Valve visible attached with two1/4" screws to
Frig frame. (Remove two screws)Tip it is a good idea to hand tighten the two srews back into their original holes. This marks their placement for mounting the NEW valve later.

6.) Inlet Valve has three water lines attached to it
and two electrical clip-on wires.
7.) Stop work and take a picture of the Valve,
which clearly shows color coded clip-on wires
and hose connection ports.
8.) Take a break and study the photo next to
the NEW valve in order to insure an OEM
match.
9.). Note: Lines push directly into ports and then you need to pull them toward you, as though you were pulling them back out of the port. This will seat and seal the water lines with a tight fit.
Tip: Cut the old line about 2-3 inches away from the old valve and check that your cut is clean, before putting it in the portal of the replacement valve. Note: You only get it right the first time, so double check your cut is square with clean edges.
Look at the lines pointed straight at you to insure the plastic hose is still round. If it is oval or slightly creased at the edges, cut the hose with a razor blade or very sharp knife until it looks good and shove in fully, until it hits bottom, inside the NEW valve. Give a firm short pull and you will feel the hose seat almost immediately.

10.) Repeat the process with all three hoses
and take another short break. Look at your
photo to guide your color matching with the
Clip-on electrical connectors.

11.) Now remove the Clip-on electrical
connectors one at a time and place on the
NEW valve.

12.) Turn on the water feed line and check for
leaks. If NO leaking is detected, congratulate
yourself, and use two 1/4" screws to mount
the NEW valve to the frig frame. The two
screws you left hand tight in the frame, show
the way.

13.). Plug in the Frig. let everything settle in for 10
minutes, while you have a break for a small
bite/drink, use the bathroom, etc.

14.) Okay time to push the frig back against the
wall. Do you want to place the old dust
shield on the back of the frig? If you are
unsatisfied with the condition of the old one,
you might consider replacing it.

15.) My wife is good at crafts, so she chose to
use the old one as a template and made a
new cover out of material she had to buy.

16.). I should tell you that I had to do this job twice, because I bought a cheap valve online that looked exactly like what I needed. It failed to work with the ice maker and after three months, it started to leak. Once again I learned "you get what you pay for."

I hope this helps one or two people get it right on their first attempt.

Good Luck, Larry

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

After taking apart the ice maker, the only obvious replacement was the motor assembly. I check various Internet sites and found the best price at PartSelect.

I removed the ice maker from the freezer after turning off the ice make switch. Removal was easy with only one screw holding in the entire assembly. The ice maker has rails that allow it to slide in and out like a drawer.

After R/R the motor assembly and returning the ice make to the freezer all that remiand was to see if it worked.

Within 10 minutes I had the wonderful sound of water filling the ice maker tray. Within 30 minutes of that, ICE!!!

Shopping, ordering and shipping of the part was fast and efficient. I'll go with PartSelect for all my future appliance needs.

Replaced the cap no tools needed

It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.

take out Ice maker tray, remove three screws holding the ice maker, unplug electrical connector. Replace with new Ice maker,Ice started to fill the tray. ENJOY!!
THANKS.

Took the old one out and plug the new one in, simply as 1 2 3. Order the part one morning,it was here the next afternoon, the ice maker was fixed in less than a half hour. we will order from you the next time.

Open your door as far as it will go. Line it up with the plastic holder should just slide into place.

Took the glass shelf out of the fridge in our rental home to clean and it just shattered in our hands. Did a search online and found part select, phoned to make sure I was looking at the correct part, the lady on the phone was very helpful. I ordered the shelf using the next day service as we were returning home to the UK within 3 days so did not want to take the chance of not receiving it before we left. I got the notification the part had been dispatched, the part was delivered early next morning. Took the shelf out the package and placed in the tray, job done!. Great service will definately use again, have book marked the site.

I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.

Removed old gasket. Wiped everything down. Popped in new gasket.
It was a little tedious, but it went in easy enough. Some reviews said the new gasket was kinked and bent. Mine I am happy to say was smooth. Some things are still getting quite cold like vegetables and ginger ale.(almost freezing). But it is way better than it was. Saved us from having to purchase another refrigerator. The fellow who helped me made it easy to order and everything went smoothly. I appreciate the help and patience you provided.
I

rippped the old one off and carfully put the new one on with a flat head screwdriver at an angle as not to rip the new one

This was a simple install. I just replaced the glass shelf on the sliding shelf bracket.