59667252701 Kenmore Refrigerator - Instructions

Unplugged the power, removed old icemaker by removing 3 screws and unplugging a small wire harness

Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on

ALL FIXED!

remove 3 screws,rotate assembly,depress lock on wire harnass connector,un plug harnass.remove old assembly,remove and transfer side cover and steel wire at front of assembly,connect harnass to new assembly,rotate into place,aling screw holes and install 3 screws.flip front steel wire down and wait for about 1 hour,first tray of ice will fall..all done.

Replaced the control of the ice maker assembly.

Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be removed and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.

There are basically three screws that hold the unit in place on the inside of the freezer. Removing them is relatively easy, and the unit is replaced with the same three screws. You do have to use the formed metal wire from your old unit, so don't throw it out! You also have to use the wiring harness from your old unit.

, to remove the inlet tube holder/guide gadget thingee: (1) remove the three Phlipscrews from the motor end of the housing. (2) pull the housing straight off the end. (3) remove two Philips screws in deep holes that hold the ice tray onto the motor housing. (4) this frees the ice tray assembly, which you have to pull out, freeing the rotating blades, from which (5) you slide the sxle out of the middle of the inlet-tube thingee, so (6) you can then remove the inlet gadget from the ice tray.

You then reverse these instructions to reassemble with the correct inlet gadget. The tricky part is the front cover that hides the ice-tray from view. That cover has a couple of ears that have to fit into mating holes in the motor housing before you replace the two deep-hole Philips screws that hold the tighten the ice-tray assembly back onto the motor housing.

So it's too bad they don't see the ice-maker assembly with all the knock-outs inplace, so you can knock out the one you want. Other than that, it would have been no more trouble than other people have reported in working in the tight space inside the freezer compartment.

I made use of instructions for other users, see 'My ice maker has been shedding.....' and they were very helpful. The one problem not covered - the instructions that came with the new icemaker said to 'remove the bearing and inlet from the old icemaker and install in the new icemaker', but gave no instructions for how to accomplish this.

The old inlet has a square opening in the back and a u-shaped knockout in the side. The new one has a round opening in the side and square knockout in the back)

After several attempts to remove them, I gave up and used the new inlet with the knockout removed. I did not attempt to cover the side opening and it worked fine that way - no leaks.

As per instructions. Removed parts from old ice maker, and installed them on new one, Then installed it in the freezer. Works good.

i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.

Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.

Ice maker assembly required disconnection of the wire harness at the back of the freezer and the removal of 3 hex nuts. The assembly did not come with a new wire harness nor the rigid wire attached to the hinge that can be raised to stop production of ice. The wire harness was easy to disconnect from the old assembly by pressing in on a tab. The rigid wire attached to the hinge simply required pulling straight out of the hinge-hole (no need to twist, slide, or perform other contortions...it does require significant force to remove, but it does pull straight out). It was simple to attach it to the new ice assembly. Reinstalled the 3 hex nuts and wire harness plug and was good to go....after waiting several hours! I was worried at first because the unit did not immediately fill with water after I plugged the fridge back into the wall socket. However, after the freezer was cold enough, the water did run and I had my first ice dump within about 3 hours of finishing the installation. We have good ice again, and Partselect has excellent pricing and awesome delivery! I received the unit the day after ordering, and I had only paid the basic shipping! Thanks Partselect! Jeff

Open the refirigerator door and push and hold the On/Off button at the top to turn off internal power. Open the freezer door and move the icemaker switch on the right side freezer wall to "off".

To get access to the icemaker, first remove a hinged plastic door that mounts to the ceiling of the freezer compartment by two hex screws. Remove the screws and the door so you can work with the icemaker without interference.

The icemaker assembly will slide out once the wireharness has been disconnected. To disconnet the wire harness, a while plastic shield has to be removed from the right side of the icemaker, just behind the water inlet.
Locate a hex screw on the bottom right rear of the icemaker and remove it with a socket wrench. Then the plastic cover can be pulled off.

Slide the icemaker out enough so you can get your fingers on the plug connector. It takes some effort to pull the plug connectors apart. Once unplugged the whole icemaker assembly can be removed.

The motor module is located on the left side and is protected by a white cover. This cover is not attached so it can be pulled off to reveal the motor module.

Remove 3 screws from the outside of the motor module and the module can be pulled out of the housing. Insert the new motor module. The module turns the shaft of the ice srapper arm. the shaft has a D shape which mates with the hole in the motor module so you may have to roatate the scrapper arm until the shaft shape matches up with the hole shape in the motor module.

Once the motor module is seated, replace the 3 screws and push the white cover back on.

Position the icemaker so you can reconnect the wireharness plug connectors. Once connected you can push the icemaker asembly back into the grooves of shelf rail. Reattach the while protector shield which covers up the wire harness plugs.

Open the refirigerator door and push and hold the power button to turn internal power back on. Move the icemaker switch on the right wall of the freezer to the "on" position and close the door.

The icemaker should start making ice within 2 hours.

Repair was real easy, I had to remove several screws in the bottom of the icemaker module housing. The unit slide out with no problem there was a wire assembly that hat to be disconnected but this did not present a problem. The old module came out real easy after removing 4 screws and the replacement was not a problem to but in.

The repair was simple.

I first did a diagnosis of the optical cuircuits and found them good. The tray heated up and when resetting the moor controller, the water cyccled to fill the tray so the only other thing it could be was the motor controller.

removed the service door for the ice maker
I removed the wire protectore screw and shroud
pulled the icemaker unit out and unplugged the unit
removed the motor controller end cap
unscrewed 3 screws holding the motor controller
removed and replaced the motor controller. ensured that all wire harness connector poiints were solid
reverse the above instructions and in 5 hours I was getting ice again!

$90 turned out to be a savings from the $250 it would have cost to have someone come out and look at the fridge.

I highly recommend to anyone who can read and use a screwdriver to perform this repair if you have diagnosed this as the root of your problem!

to easy to describe, remove 3 screws and a wire plug then install new unite.
Works great
Thanks