2536080440J Kenmore Refrigerator - Instructions

Thawed out freezer, I recommend laying a couple old towels in freezer to soak up melted ice. Replaced old thermostat with new part. Removed 2 screws, removed back plate, unplugged 2 connectors and cut 2 wires. Crimped in new thermostat and repositioned to original part location. Reconnected plugs as I reinstalled back plate. Installed 2 screws and connected power. Works like new! Trouble shooting and part installation video is very helpful, great site!

inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!

I followed the instructions on your website, made it a simple as possible. Very tight work area sometimes fingers only, but a little patience works.
Saved at least $300. By not paying a repair person.

Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other parts, but not happy that the actual part I needed was not available - had to use other methods.

Before buying the part, I watched your video and realized it was extremely simple to remove and replace. Item was to take 7-10 days and I received it in 4. Took longer than 15 minutes because I had to move the fridge forward, get my tools and a vacuum, get a cup of coffee and get to it. Very easy and the video was exactly step by step. It took longer to vacuum all of the dust bunnies than to replace the part.

Honestly, I was in the market to buy a new refrigerator but now I believe I'll wait several more years. Thank you for your support.

Just like the video , just pull out the crisper drawers and slide the new one in. I also made sue that I had a quilt on the floor in case I dropped the glass shelf. Also if you are not sure of the model number you can try calling the store where you bought the appliance at which I had to do. I bought it at Conns and they just needed the phone number I used when I bought it.

Pulled off the old seal and put the new one on. No tools needed. It fit where it was supposed to and seals the door like new now! Thank you!

Easy to peel out old gasket, and new one tucked right in. I was embarrassed that it was so easy and I waited so long. Has made a big difference in how the frig looks and also operates.

Putting the shelf in was a no-brainer. It comes with matching slots and you can't put it in upside down or backwards. Only the right way!

There is no way to complete the repair with the wrong part, You have had my order since June 22nd, 2020 and the incorrect part arrived October 27th, 2020. You charged $7.79 plus $1.06 tax and $9.95 shipping. Please refund the entire amount including the shipping, since I did not ask you to ship the incorrect amount.

Just slide glass in. Very easy.

Just slid it in. Fit perfectly. Called the Help Line just to double check that the pan would fit and they assured me it would. Pan cost $20 less than through the Sears site because of lower price, lower shipping and no taxes. Oh, and the pan came in just two days. Very happy.

I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.

The bulb wasn't the issue so I was hopeful the switch was. utube helped me some, but figuring my model was different than any on utube. Got the switch in and plugged it back in. Moment of truth. Didn't light. Ugggh! Out $50 for switch plus $20 for nut driver set.

I used the youtube you provided. It was pretty straight forward, but I had to make a trip to the hardware store for a bit (hex wrench) to remove the hex bolt head style screws. I was only expecting to need phillips or flathead. I managed to remove one with a set of pliers, and the brought that example to the store for size reference when buying the bit to fit my black and decker drill. The rest was easy.

Remove lower cardboard refrigerator panel. Carefully pull existing cracked fan blade off of the motor shaft and replace with new fan blade. Reinstall cardboard panel.