59676052701 Kenmore Refrigerator - Instructions

Cut old fill tube into pieces, removed and replaced with new tube. Extremely easy.

Caused the shelf on my fridge to break a ladder hook. I didn't even know where to begin looking for an Amana refrigerator shelf mount bracket, but luckily found this website from a Google search. The part was super easy to find, arrived in two days, and was a snap to install. What did people do before the internet?

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Bought a new shelf

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Take everything off the top self, lift the self install the new part ,put self back in place and then install the drawers again. Took minutes.

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Unplugged the unit took back cover off unplugged start/run cap,plugged new one on,put cover back on,removed freezer drawer, removed back panel in freezer, cut wire to old thermistor, wire capped new one on to existing wire,put back panel on,put freezer drawer back in,plugged unit back in

Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattaching rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!

I replaced the Control Board...
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..

Super simple following the instruction video you posted. Thanks!

Followed Youtube video from Free Repair Help. Only problem was getting down low enough to see the pins on the Compressor to plug the replacement Compressor Start Device and Capacitor-could not replace the old clip to hold the unit to the Compressor like the old unit had. At 77 I just have a problem bending over.

I looked at a video on YouTube that described how to check if the water inlet valve was working. By using an ohm meter, it indicated the water valve was bad. I could hear the ice maker trying to make ice. I ordered the part; it was shipped that day. The email confirmation also had a video on how to change. I watched and changed it out quickly. The valve is easy to take out by disconnecting the water line and quick disconnect electrical line. (Turn off water and unplug unit). I took pictures of my steps so I could remember the valve orientation. The new valve went in the same way in just 2 minutes. I needed a 1/4 inch nut driver.

We had a full ice tray in 24 hours.

Our freezer door handle popped off and I learned how to put it back by watching a YouTube video.

I am not handy at this type of repair but this was a great experience. Thank you!!

I had previously replaced the defrost timer and thermostat but the freezer was still not cold enough and was frosting up. After replacing the heater element I was disappointed that all the ice melted and the refrigerator was warming up. We were looking for a replacement appliance, but after the second day the freezer and refrigerator were working perfectly! It just took some time to cycle enough to catch up.