25374222704 Kenmore Refrigerator - Instructions

Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wiring harness plug, replaced the old timer with the new one, re-connected the wiring harness and reinstalled the mount in position. Hardest thing about it was lying on the floor.

Turned off fridge circuit breaker
Removed all food from freezer and put in cooler.
Removed shelves from freezer
Removed ice maker
Removed 2 hex head screws
Tilted back evaporator cover and tried to unplug connection.
Found connection was iced over with a huge block of ice coming from water inlet to ice maker
Spent several hours trying to melt and chip away ice without damaging fridge.
Finally was able to break up ice with long flat head screwdriver and hammer.
Unplugged connector and was able to remove evaporator cover.
Cut wires near thermostat and removed
Stripped wire as needed and crimped new thermostat in place.
Used heat gun and lighter to melt heat shrink. This took a long time and required a lot more heat than expected.
Reconnected evaporator cover connection and reattached cover.
Reinstalled ice maker
Reinstalled shelves.
Put food back in
Turned circuit breaker back on.

Replaced thermostat and defrost timer and still freezer to warm.
After research with U-tube video of (Fixin it with Pappy) discovered that my fridge has one thermostat in fridge section and in cold months (live in ohio)the garage is cold therefore themostat in fridge does"nt need to tell the compressor to kick on. Pappy is a retired engineer and in very easy to follow instructions will show you how to fix this problem. Strongly suggest to search for his video on Utube. I did as he instructed and my fridge freezer works great in cold weather now. Its apparent to me I wasted my money on the parts. I didn't` need to replace. Just happy my Beer fridge is working all seasons now.
John from Ohio

You tube is my best friend for DIY repair. I supported the door with wood blocks, removed the bottom bracket and was able to slide the refrigerator door down and out without removing the freezer door. Replaced both hinge bearings and door stop and washer on bottom hinge and slid the door back into place. Door is very light when empty. Fast and easy, door opens and closes smoothly and no problem with condensation anymore.

Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

Not knowing the history of the refrigerator/freezer and observing that the icemaker would cycle (ice ejector fingers would rotate when the off/on arm was toggled), I concluded that the water valve must have some hard water scale in it which was causing it to stick. I replaced the water valve and the exact same behavior continued. By elimination, I concluded that the microswitch in the icemaker must be sticking. I removed the icemaker, used a hair blow-dryer to heat/dry out the microswitches and then a little shot of WD-40 on the mechanical arms, switches, and cams fixed it.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Unscrewed old bulb and put in new one

Replaced bad parts with new parts it went easy

I ordered the part from PartSelect using the part number located on the valve itself. The part was delivered in less than 48 hours from the time I entered it. Replacing the valve was easy and went according to the online video instructions provided by PartSelect. The only thing extra was that I had to replace the brass compression fitting on the copper tubing connected to the inlet of the valve. The old one would not seal properly. The compression fitting was about $1.50 at Home Depot. This is my third purchase from PartSelect and I continue to be impressed by them.

I broke the glass shelf in my refrigerator. I had trouble navigating the website, so I called the customer service line, and the lady was lovely to speak with, and ordered my part quickly! In 2 days I had the part, and it fit perfectly!

Great service, great price!
Thank you!

I ordered a replacement on-line (real simple, visual aids helped more than model nos). Once I received it in the mail, I installed it (no tools required) and now my water filter and ice maker are back to doing what they do best!

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.