10644569600 Kenmore Refrigerator - Instructions

The refrigerator light in our Kenmore fridge has been flaky for a number of years. The slightest bump would knock it out of the hole it fits into leaving the bulb dangling. Usually since we were used to it, we could avoid bumping it so it was no real problem, but a recent visitor bumped it and it once again was hanging. I decided this time, to take a serious look at it and fix the problem for real. I had options, duct tape, hot glue gun, goop...or a new part! A quick search on the internet, and I found www.PartSelect.com I entered my model # , quickly found the correct part number. The part came 1 1/2 days after I ordered it. The repair was very simple, I unplugged the fridge, removed the wires from the spade connectors on the old light socket, and attached them to the new socket. I then pushed the socket into the hole, and with new spring clips, it snapped snuggly into place. The socket came with extra wire connectors which I didn't need, the socket fits multiple brands of appliances. It also came with a bulb protector, but that wasn't needed for my fridge either. I was very pleased with the speed and ease of the repair. No more dangling light bulbs!

Super-easy... First, empty refrigerator door. Then, just remove the bolt that goes through the cover over the top hinge. This exposes three more small bolts. Remove these and the top hinge assembly will lift off. Lift door off. Remove cam from door and lower hinge, slip new cams on, and reassemble. The hardest part was pulling all of the junk stuff out of the refrigerator door. Who know you could accumulate so much salad dressing?

Pot the part on

It took just a few seconds to snap the shelf into place. Thank you for sending the part so quickly.

Fit in perfectly. Slid out the old one, replaced with the new one. Very easy. Very satisfied with the transaction.

I was first reluctant to start poking around, as I am limited in my handyman skills. However, not wanting to spend a lot of money, I decided to get my hands dirty. I quickly identifed the problem being the run capacitor and overload protector. I then identified the parts I needed to order using partselect.com and looked at user stories. I was confident this would work. Ordered the parts (YOU NEED TO ORDER TWO PARTS!) and began replacement. However, one of the prongs that the part connects to, broke in half. I was able to fashion a copper sheath to serve a conductor and to my amazement it worked. Had that hiccup not occurred, this would have been a mighty easy fix. Everything about this site helped and defintely gave me a "Tim the Toolman Taylor" boost of confidence.

Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,

Easy, peasey. I popped the old one out and put the new one in. Less than 30 seconds.

Emptied door of food jars etc. Used socked on top plate. Removed door and placed on a flat surface. Used socket to take out cam on the bottom of the door. Replaced worn cam. Replaced nylon sleeve on the top of the refrigerator door with needle nose pliers. Placed door in the bootom slot with the new cam in place. Placed top plate in the new nylon sleeve on the door. Replaced screws with socket wrench.

I ordered two new ones from partselect.com. I figured if I was replacing the one for the refrigerator door I might as well do the freezer door too.
Very easy to take the old ones off, take the putty knife clean tracks out. Putting the new ones on, was a little harder to do. You have to start in the corner and push the gasket into the slot. You need strong hands to do this. Once I heard them click in, they guided themselves the rest of the way. Once they are on, check to make sure they touch the frame of the door. My freezer was perfect, but the refrigerator had an area of 25 inches that did not touch the frame. I called partselect.com and they sent out another new gasket for the refrigerator door. (I had to pay for this one but was told once I mailed in the defective one, they would credit me the cost of the returned one) I took off the bad gasket and installed the 2nd new gasket and that one was perfect.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Removed old switch and installed new - but did not solve problem

This story is less about the repair than the service. On Monday, I removed the meat drawer to give it a quick rinse. Unfortunately, I fumbled the ball getting it back to the fridge, dropped the drawer on the hard stone floor, shattering it.

Instead of calling a repair man or going to the local appliance store, I opened up my macbook, found partselect.com, ordered the part and they had it taken care of in 5 minutes. Two days later, Fed Ex handed me a box with the replacement drawer, and I slide it in. Done. Total time to repair -- 6 minutes.

Sure beats leaving the house!

got the icemaker kit and started to add it to the frig found problems with the adaption to the frig in back for water filler tube but was able to make it fit. had to make a connection outside to water line with copper pipe added to hose with claps and saddle valve, turned it on and had leaks due to the schedule copper was the thin wall type, got thicker type and installed it, no leaks, started making ice. it was nice to get the right kit to make things work out. thanks

just slide the new compartment in