10646032801 Kenmore Refrigerator - Instructions

We popped out the new filter and replaced the cap with a twist. It was so easy. It is important to vaccum the front of the refrigerator for accumulating dust.

Fit in perfectly. Slid out the old one, replaced with the new one. Very easy. Very satisfied with the transaction.

Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,

I unplugged the fridge, removed the face plate on the front, disconnected the power feeds, unscrewed the electrical panel and moved it out of the way.
I then dismantled and removed the broken part and installed the new part. I was able to use the rest of the existing parts to get the job done.
I put everything back together, and voila! it works great.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Because of the design change of the door hinge it was more difficult to slide the pin into the door and spring. I used an allen wrench to hold it in place on the left side so I could slide the pin in the right hole. Then removed the allen wrench so I could slide the pin all the way. I was very impressed with the time that it took to get the kit. I ordered it about 1:30PM and the following day I had the kit delivered by 6PM. FANTASTIC SERVICE!

Very easy doit repair. Watched Youtube video helpful. Small nut driver and flashlight the only tools needed. Ordered part with standard delivery and received the new motor in under 24 hours! Impressive. I will use Part Select again! So happy to have a working augur. No more stale ice at the bottom of the bin. No more scooping ice with fingers!

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

Long shaft from motor to dispenser was stripped. I removed 2 screws from the shaft holder in door, lifted old shaft out, put new shaft in and replaced the 2 screws. Took 2 mins! Works great!

The cap will only fit on one way. Align with tabs on filter, twist on. Press the filter into place and press to seat. Locks into place.

Removed Ice container; Removed two screws from housing around shaft; Pulled old shaft from freezer door; inserted new shaft in freezer door; replaced housing around shaft; replaced and tightened two screws securing housing; returned ice container. Tested by activating ice dispenser. It worked like new.

I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Piece of cake. It took me longer to remove the food from the freezer, remove shelves and back panel than to do the repair. I heard the fan making some noises so I replaced both the fan and defrost thermostat. I used the instructions submitted by a another customer. My 20+ year old fridge is like new now.