25360892406 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janette St from KALISPELL, MT
- Parts Used:
- 240534701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Had a broken part in the door that holds condiments in
Removed broken part and then snapped in new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PHILADELPHIA, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Evaporator was freezing up and was running non stop
I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Okeechobee, FL
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Intermittent loud noise coming from fan motor located in freezer compartment
Ordered a new evaporator fan motor and watched the repair video supplied by part select on their web site.It was spot on step by step instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from New Fairfield, CT
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper glass shelf shattered during cleaning.
Extremely easy repair for a 76 year old woman. I just followed the very clear video instructions provided with my order and my fridge was as good as new within 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from HASKELL, NJ
- Parts Used:
- 241839405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
bought brand new and kick plate was missing
just snap it on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from FREDONIA, KY
- Parts Used:
- 242193213
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My gasket was worn out and torn.
The repair was much more simple to install than I would have imagined. I watched the video provided on your website. What a simple solution to a nagging problem. My fridge looks great again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricky from BUENA PARK, CA
- Parts Used:
- 242193213
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GASKET OLD LEEKING OUT COLD AIR FROM FRIDGE FOOD WARM
SO SIMPLE I JUST FOLLOWED THE VIDEO THE PARTS SELECT PROVIDED ON THERE WEB SITE AND WALA DONE IN 5minutes Wow THAT EAZY NO TOOLS NESSECCARY JUST A SCREWDRIVER
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elyse from NEW ORLEANS, LA
- Parts Used:
- 241872503
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
It would have been nice to fix item I paid for but I never received it.
I tried contacting this page about the item I never received but I never heard back so this is my review. I DIDNT FIX IT BECAUSE I DIDNT GET ITEM.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from NEWHALL, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Evap fan motor comes on and off will not stay running
pulled back panel to get at evap fan motor cut wires to remove reinstalled hooked up wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aaron from ODESSA, TX
- Parts Used:
- 5303918549, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Fridge was't cool
I just followed the instructions on the videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from CAPE CORAL, FL
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
FREEZER COMPARTMENT NOT COLD ENOUGH (20 DEGREES)
REPLACED TIMER-DEFROST 215846602..REPLACED THERMOSTAT-DEFROST KIT 5303918202..REPLACED CONTROL, TEMPERATURE 5304421256..RECHARGED SYSTEM WITH 134A...ALL FANS WORKING...COMPRESSOR RUNS.. FREEZER STILL NOT GETTING COLD ENOUGH...HOLDING AT 20 DEGREES...ANY SUGGESTIONS..THANKS..DAN
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cristina from MARLBOROUGH, MA
- Parts Used:
- 242193213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Old gasket was torn and falling out
I removed the old gasket and cleaned the area. Then I started at the bottom and pressed the new gasket into the door. You must use firm pressure and go all around. It does get tricky hear the end as it seems like there is excess, but it will fit. Just keep using firm pressure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karla from UNION, MO
- Parts Used:
- 241554901
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Refrigerator light stopped working
The bulb wasn't the issue so I was hopeful the switch was. utube helped me some, but figuring my model was different than any on utube. Got the switch in and plugged it back in. Moment of truth. Didn't light. Ugggh! Out $50 for switch plus $20 for nut driver set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from FRANKLIN, TN
- Parts Used:
- 240524102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Noisy condenser fan
Remove lower cardboard refrigerator panel. Carefully pull existing cracked fan blade off of the motor shaft and replace with new fan blade. Reinstall cardboard panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from VIRGINIA BCH, VA
- Parts Used:
- 241554901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Door switch was no longer making my light go on when door opened
I used the youtube you provided. It was pretty straight forward, but I had to make a trip to the hardware store for a bit (hex wrench) to remove the hex bolt head style screws. I was only expecting to need phillips or flathead. I managed to remove one with a set of pliers, and the brought that example to the store for size reference when buying the bit to fit my black and decker drill. The rest was easy.
Was this instruction helpful to you?
Thank you for voting!