59667254701 Kenmore Refrigerator - Instructions

Removed and disconnected the icemaker, cleaned all areas and disassembled the failed parts. Reassembled with the new parts inlcuded with the purchased package and resinstalled the unit. Started the unit and chedked for proper operation. Successful repair.

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by taking out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl

Unplugged the frig., removed three screws, pulled the motor out, then slid the new motor in. Within a few hours I had ice again. The only problem was I felt the motor was still hooked to something after I took out the screws. Just be firm and pull it out, the pressure you feel is the thin bar that slides into the back of it to monitor the level of ice in the tray. It was REALLY easy.

I found your website while searching the internet for a repairman. My fridge was making strange clicking sounds and no ice. I suspected a certain part after reading the testimonials on your website. The part I ordered was delivered in less than a week and I installed it in less than 5 minutes. I probably saved about $200.00. Thank you!!!

1. Removed all 4 screws underneath with nutdriver
2. Whole assembly slides out like a drawer
3. Unplugged power/wire harness
4. Removed Motor Assembly - 3 screws
5. Found the broken plastic wheel
6. Ordered part on PartsSelect
(Total: 5 minutes)
7. Received new part next day
8. Put the new motor assembly back on using the original 3 screws (it doesn't come with new ones)
9. Slid unit back into drawer
10. Put the 4 Nut Driver Screws back in (tricky to get the wire harness cover back in place, but not that bad)
11. Plugged in wire harness
12. Turned on the ice-maker
Ice Dropped within the hour.

Read on line that the motor module in the ice maker was likely to be the problem. I ordered the part and it came in as a complete module. All I had to do was to remove the cover, take out 3 philips screws, remove the old module and install the new one. I plugged it back in and had ice within the hour.

By replacing it with a new ine maker.

Very easy to install the new ice maker. Removed the bottom screw holding the ice maker to the side of the freezer. Loosened the top two screws. The old ice maker came off just like that. Unplugged the power supply from the freezer and removed the whole apparatus.

I saved the wiring harness, screws, cover, and metal arm from the old ice maker. Installed these on the new one and mounted the new ice maker in the freezer. Done.

The only issue I had was that the water supply hose got kinked when I pushed the fridge back into place. Once that was resolved, the new ice maker started happily making ice.

Open the icemaker service, door slide it out, remove wiring, remove ice maker control cover,remove 3screw, put new one in, put everything back together and with in 6 hours we have ice again. PS my husband did it though.

Your youtube ..order part and fix in 2 mins.AWESOME we had our refrigerator since 1983.... my wife keeps her looking new...& happy with the saving .Our frigerator a MAGIC CHEF..the ice maker is the only thing we have replaced.

I performed basic troubleshooting to make sure there was power and water. Based on historical research on this particular ice maker, I decided that the best direction was to replace the entire assembly. I found this item on this site, ordered it and received it a few days later. I basically removed the ice pan and a few items in the freezer, removed the three mounting screws with either a flat blade screwdriver or nut driver, pulled the electrical harness out of the back wall of the freezer and transferred it to the new ice maker and then installed the new unit, really that simple. Iwas concerned at first, not seeing any activity in the new ice maker but after 15 minutes or so I heard ice falling into the ice bin. Well worth replacing seeing how simple this job was.

Removed the elec connection (after unplugging app) found it easier to remove from appliance. Remove the three screws ( do not temove,....just loosen, the top two) bottom must be removed! Insert the power connection, exchange the tilt up rod, line up the water connection and place back on the two top screws. Tighten and relpace the bottom screw. I found out the hard way.... you cant't see the two top screws . The slots on the ice maker just fit over the screw heads.... it's cold in there!!!

Hopoe this helps..

Cape Cod

Removed old ejector arm and installed new part.

When I took the ice maker apart I noticed that the shaft of the motor control wheel was broken so when it turned it could not trip the control contacts nor rotate the ice ejector fingers. I ordered a new control and motor assembly which arrived two days later. It was very easy to install and now the ice maker works perfectly.

PartSelect was a great help. A local appliance parts warehouse stocked parts for my ice maker but they only stocked a kit that contained other parts that I did not need. Ordering from PartSelect saved me over $35.