2537088240K Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from PHILADELPHIA, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Evaporator was freezing up and was running non stop
I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janette St from KALISPELL, MT
- Parts Used:
- 240534701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Had a broken part in the door that holds condiments in
Removed broken part and then snapped in new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from HASKELL, NJ
- Parts Used:
- 241839405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
bought brand new and kick plate was missing
just snap it on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from HOISINGTON, KS
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice Maker not producing / Clicking / Off-cycle
We love our ice here. I seem to replace the ice makers one to two times a year. Generally the ice cycle gets off for some reason and it starts making loud popping/clicking noises (gear grinding). Its easy to replace. Simply loosen two screws holding the unit to inside of freezer and disconnecting the wiring harness. Unit slide up and out. Replacement is super easy (5 mins or less). Bam! Ice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from PANAMA CITY, FL
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker broke again!
This refrigerator is less than 2 years old. I have had to replace the ice maker 2 times now. Cheap ass parts! Only one ice maker you can order so just be prepared to replace it yearly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MONTGOMERY, IL
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Coils frozen over. Refrigerator not cooling
I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Salvador from SANTA ANA, CA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Freezer worked, refrigerator didn't. Ice build up on coils.
Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carey from PORTSMOUTH, VA
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Didn't make ice
Unplug refrigerator , loosing two screws. Lift ice maker up to remove from position. Disconnect electrical connection. Reverse procedure to install new ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elyse from NEW ORLEANS, LA
- Parts Used:
- 241872503
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
It would have been nice to fix item I paid for but I never received it.
I tried contacting this page about the item I never received but I never heard back so this is my review. I DIDNT FIX IT BECAUSE I DIDNT GET ITEM.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bay City, MI
- Parts Used:
- 5304464438
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Fridge quit working.
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cristina from MARLBOROUGH, MA
- Parts Used:
- 242193213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Old gasket was torn and falling out
I removed the old gasket and cleaned the area. Then I started at the bottom and pressed the new gasket into the door. You must use firm pressure and go all around. It does get tricky hear the end as it seems like there is excess, but it will fit. Just keep using firm pressure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from VIRGINIA BCH, VA
- Parts Used:
- 241554901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Door switch was no longer making my light go on when door opened
I used the youtube you provided. It was pretty straight forward, but I had to make a trip to the hardware store for a bit (hex wrench) to remove the hex bolt head style screws. I was only expecting to need phillips or flathead. I managed to remove one with a set of pliers, and the brought that example to the store for size reference when buying the bit to fit my black and decker drill. The rest was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- henry from alhambra, CA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
my ice maker stopped working
removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from CAPE CORAL, FL
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
FREEZER COMPARTMENT NOT COLD ENOUGH (20 DEGREES)
REPLACED TIMER-DEFROST 215846602..REPLACED THERMOSTAT-DEFROST KIT 5303918202..REPLACED CONTROL, TEMPERATURE 5304421256..RECHARGED SYSTEM WITH 134A...ALL FANS WORKING...COMPRESSOR RUNS.. FREEZER STILL NOT GETTING COLD ENOUGH...HOLDING AT 20 DEGREES...ANY SUGGESTIONS..THANKS..DAN
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACOB from YOUNGSTOWN, OH
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Refrigerator did not cycle
Installation was fairly straight forward. The major complaint is that the problem returned 2 weeks later. I don’t know if I care to re-invest in another switch.
Now what?
Now what?
Was this instruction helpful to you?
Thank you for voting!