10651143110 Kenmore Refrigerator - Instructions

Like you video

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.

Just follow youtube examples. Work in freezer. Troubles was I didn't fix the problem. Experts say thermostat is the best one to replace (53%). Anyway they are not always right.

with vidio

inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."

We emptied out both sides, refrigerator and freezer, and followed the instructions in your video. We turned it off and disconnected the power. We took off the freezer door first. It made it much easier to get the shelves out and reach way back into the freezer. We removed the light and cover, then the ice auger motor. The back panel was easy to lift and remove. The wire assembly was a little hard to understand at first, but when we figured it out it was easy to remove and replace the bimetal defrost thermostat. We did check the video when we had the wire harness out, to make sure we got it right. We reassembled the freezer's inside parts and reattached the door. Before we turned the power back on, we scrubbed down the entire refrigerator. When we turned the power back on, the refrigerator and freezer were operating quietly - no sparks or explosions or shorting out - hooray! And the problems were solved.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.

Remove the ice bucket and check that the auger that turns in the ice bucket is free to turn. Cover the open freezer with cardboard or whatever to retain most of the freezer temperature. Remove the holder that supports the top of the motor shaft. Check the splines on the upper part of the motor shaft and also check the seal under the holder. Open the access the door to the motor, remove wiring connector and unbolt the motor. Check the lower splines on motor shaft for condition, clean the shaft and apply new grease to the splines. Before installing, connect the wiring to the new motor, push the door switch in, press the ice dispenser arm outside the door to make sure the motor runs. If all ok, check the motor shaft for fit in the new motor. Be careful not to install the motor shaft too deep in the motor splines, otherwise there may not be enough spline showing on the top end to engage the auger. Bolt the motor in place, close access door and install the holder and ice bucket and make sure everything works. If there is not enough spline showing thru the holder to engage the auger, take pliers and pull the shaft up a bit. This seems to be a hit or miss fit on the shaft but you can adjust the height of the shaft without taking every thing apart again. That's all, not difficult at all. But do check parts and pieces for anything else you might need, parts wise, before ordering the motor by itself like I did. Shipping is high, so try to order any associated parts needed when you order the motor. By the way, This site are great to work with!

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Opening up the Evaporator Fan section was a quick and easy job. After opening, I checked and removed the fan and looked at the grommet. The grommet on the fan was tight and secure and I could no longer hear the noise. I closed the opening. Something I had done while checking the fan grommet must have solved the problem. I have not hear the noise again!

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Removed 4 bottom screws. Removed module screws. Replaced module and motor with new parts (came assembled). Replaced module screws and installed the ice maker with the 4 bottom screws.

1) Turn off the power to the refrigerator 2) Remove the top shelf and ice maker door 3)Remove three hex screws holding the ice maker in place, 4) Unplug the electrical cables and remove the ice maker 5) Remove the plastic cover to the motor module 6) Remove three screws from the motor module and seperate from the housing 7) Remove two mounting screws for the motor module 8) Seperate the motor module from the ice tray 9) Remove and replace the plastic ice stripper and rake10) Reassemble in reverse order. Note: Be patient after re-installing the ice maker. It might take an hour or two before its cold enough to kick back on and make ice.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing