25361724017 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ty from GREEN BAY, WI
- Parts Used:
- 240535101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broke door rack trying to clean it
Install by sliding the rack directly down above the fridge's tabs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MONTGOMERY, IL
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Coils frozen over. Refrigerator not cooling
I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Salvador from SANTA ANA, CA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Freezer worked, refrigerator didn't. Ice build up on coils.
Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from AXSON, GA
- Parts Used:
- 240535101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My door rack broke
All you do is snap it on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from Essington, PA
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original shelf cracked and fell off. No glue or tape would hold.
Just snapped the item into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- francine from brick, NJ
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacing broken door racks
Super easy it took no more than 5 minutes to replace the fridge door racks. Starting from opening the box when it arrived to closing the fridge door with the new racks in place. no tools needed, except a knife to open the box.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W. Noah from Leominster, MA
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Kid broke to bottom door rack
This was so easy it took longer to open the door than it did to install the rack. WOW. Nice to see something fits without messing with it. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mordechai from Brooklyn, NY
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Easy and simple!
had it done in 5 seconds!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from VENICE, FL
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator evaporator coil was icing up
The evaporator coil is behind the freezer. Remove the rack that makes the shelf and remove two 1/4” hex head screws I the back of the freezer to access the coil.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from STURGIS, SD
- Parts Used:
- 242018404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
noise fan
Remove fan bracket from refrigerator, remove fan, remove motor, remove bracket and motor. apply in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from vandergrift, PA
- Parts Used:
- 240524102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
while cleaning the condenserI accidentally hit the fan blade and broke it
Had my 3 year old remove the 4 screws to holds the carboard in place. Pryde the old fan blade off with a screwdriver. slid the new fan blade on to the shaft then my 3 year old put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from AuSable Forks, NY
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
warm fridge, cold frosty freezer
remove food, then the shelf, then use a hot air gun to defrost and loosen the back panel, then remove the panel, then defrost the coil and thermostat area. using wire tools, replaced the defrost thermostat,and re-assembled freezwr and test
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Kiefer, OK
- Parts Used:
- 5303918774
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
broke fan blade while trying to remove dust.
Removed old fan motor and installed new one.Not much room for big hands back there.Flexible extensions valuable on this job.
Was this instruction helpful to you?
Thank you for voting!