25371752800 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George from Sunnyvale, CA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No freezing or cold in either freezer or refridgerator - compressor did not run.
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from CORP CHRISTI, TX
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ICE MAKER NOT MAKING ICE.
LOOSENED THE TWO SMALL SCREWS THAT HOLD THE ICE MAKER UP INSIDE THE FREEZER. DISCONNECTED THE WIRING HARNESS. TOOK THE OLD ICE MAKER OUT AND JUST INSTALLED THE NEW ONE IN REVERSE ORDER. LATER THAT DAY I HAD FRESH ICE FOR THE FIRST TIME IN WEEKS!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from Essington, PA
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original shelf cracked and fell off. No glue or tape would hold.
Just snapped the item into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from CHATSWORTH, GA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
the gear was stripped on the old ice maker and had to be replaced
was very easy. just ordered a new ice maker which was delivered in a few days. The installation was so simple. Just plugged the new ice maker in and hung the unit on the 2 screws. And then tightened the screws with a 1/4 in nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcus from Pine Hill, AL
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
frezzer iceing over and not cooling the refrigerator
Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from Kirkland, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
freezer worked frig was warm. Ice maker is still not working
Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LUIS from CENTENNIAL, CO
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer built ice, fridge not cold enough and running constantly.
Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Defiance, OH
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
leaking water down into fridge
just like the video showed...it was excellent!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Stuart, FL
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
coil Iceing up
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from merrillville, IN
- Parts Used:
- 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Heater not coming on - coil frosting up- freezer and Refrig. warm
The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cary, NC
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Freezer was not cooling.
First of all I am 78YO, retired. Handy but NOT a handyman. There were two parts to replace. The Defrost Timer was very very easy and went just like the video. 20 minutes at the most. No surprises with only the most basic tools. The Defrost Thermostat was a little trickier. Took about 1 1/2 hours. The Thermostat disconnect plug was not like the video and was stuck hard. Had to use two needle nose pliers to finally get it apart. The rest went OK. The shrink seals were way too large for the job and my Hair Dryer was not able to shrink them enough for a good seal. Used a much smaller shrink seal that a friend had and it worked great. Suggest they use a smaller shrink that works with a hair dryer instead off the blow gun in the video. Wrapped the connection with electrical tape as others have suggested in addition to the Shrink Seal. Went together easy and am very very happy camper. Saved $295 from the Sears Repair Estimate. Dave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Salem, NH
- Parts Used:
- 241796405
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
leaking water onto the evap fan freezing causing alot of noise
1st a changed the defrost stat. Waist of time. Realized there was no evaporator above fan. Noticed ice was builing up behind ice maker near fill tube. Found if I shut off ice maker ice wasnt building up on fan. Moved fridge out unplugged fridge unscrewed plastic nut. Turned 90 degrees. Replaced tube locked in place . Screwed nut back on . Plugged in and turned ice maker on. Wife happy ice was back on and no noise.
Was this instruction helpful to you?
Thank you for voting!