2534450360B Kenmore Refrigerator - Instructions

removed ice maker box and disassembled crusher unit on front of box and installed new housing.

Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!

removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine

Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.

First I took both bolts off of the housing (holds filter) and removed two hoses by holding elbow vavle in while pulling hoses. Did the reverse to replace. The trick was knowing how to remove the elbow valves. Second there was still water leaking under the fridge, discovered it was the water inlet valve underneath. Ordered that part.

Removed the Plastic Cover at the top of the door. (One Phillips Screw ) Removed the Hex Screws with socket set. Lifted EMPTIED door off bottom hinge. Pulled the broken bearing out with needle nose pliers. (Very Easy!!!) Placed new bearing into slot and reversed the procedure. 15 minutes tops. I spent more time cleaning the door and gaskets than replacing the parts. Funny thing, I called the local appliance parts store and they stated this is a common problem. However, for such a common problem, they didn't carry the part and it would have cost more than what I paid here. Additionally, I paid for 3-5 day delivery. Part was here in 2 days. Awesome!!!! I'll always come here first for all my parts needs. A+++

loosen 2 screws
unplug connector
remove
replug
replace
tighten 2 screws
done

The untwisted the water filter took out the old water filter and replaced it with the new one and twisted the cover back on. it was very easy to do and now the water tastes very fresh :) thank you

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.

removed fan unit from frig and installed new motor and then replaced back in frig. No tools needed. need to unplug unit and take apart and put new motor in the unit and then plug back in.

Pull refrigerator from wall and disconnect the water line and unplug the power.

On top of the icemaker, two machine screws hold the icemaker to the side of the refrigerator. You will have to feel around to find the machine screws, but once you do, it is simple to slip the appropriate size socket over the hex heads. I found it helpful to have an extension on the socket wrench. Disconnect the power cable inside the refrigerator (there are little pressure clips on the side that help release the cable) and move it out of the way for the time-being.

Back out both machine screws several turns, but do not remove them completely. The icemaker slips over the screws, so leaving them in the side of the refrigerator makes that process a lot easier. Hand tighten the machine screws once you have positioned the new icemaker in place. One thing to be sure and do is make sure the water line hose coming out of the back of the refrigerator inside is on top of the icemaker. It fits into a slot in the top of the icemaker - failing to do this will result in water pouring into the freezer compartment, not into the icemaker..

Reconnect the power cable to the new icemaker and tuck it up behind the icemaker assembly. Tighten the machine screws completely, but do not over-tighten.

Reconnect the water line on the back of the refrigerator at the wall, and plug in the refrigerator. You should hear the unit fill immediately.

In about an hour you should have ice filling the bin. Enjoy!

First I removed one screw holding top hinge trim in place. I than removed two screws holding top hinge from refrig. I removed refrig door and laid it on a table. I than removed two screws holding the door stop and bearing hinge. I replaced the defective parts and reassembled in reverse order. Simple 10 minute repair.

We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.