59666032602 Kenmore Refrigerator - Instructions

Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.

Removed both crispers and shelf . Inserted new rail as explained in video. Replaced everything.

Removed the glass shelf, position the rail in its slots and replaced the glass shelves.

Followed easy instruction video. It was like new in fifteen minutes.

Thanks to some reviews we found online about replacing gaskets, ours went very smoothly. One person said to soak the gasket in hot water, which we did til it was very soft. Installed like a breeze. Then, the same person said to tape the door closed after installation, we did that too. The gasket looks like it was professionally installed and we have never done it before. Thanks!

first unplug unit, remove clear light cover it snaps out. there are 2 slots on either side of the light housing stick the screw driver in the slot and push the tab and pull down this will unlatch the control board housing, remove the board socket plugs, and the board from the frame, on the new board you will have to snap the PC board at the pre indented line. replace in reverse and follow instruction to program the code.

I watch a widea on part select 'how to do that' and was relly very easy to repleace a part. The delivery was next day. They are triting customers very serious and professionals. I'll recomended part select for all my friedds with similar problems. Thank you.

Replaced the CNTRL-ELEC board with ease. Just slide back and remove the light cover. Use flat tip screw driver to release and drop down unit. Remove connectors and attach to new board after breaking in half to fit same as old one. Programming is easy, just look at the CODE on the name plate inside the door. Mine is 0-1. Follow procedure of holding the light switch off while touching the freezer control 3 times within 10 seconds. A "P" for programming will appear. Still holding the light switch, touch the refrig control to set for your code. Freezer button says 0, refrig button says 1. When you release the light switch, the programming is done. Mine starts out with a 4-4. It is now working quieter than when it was new and is very cold again.

Found troubleshooting steps for control board (called a jazz board) and ran through the steps. Found the control board (jazz board) was bad. Pull front vent cover where the condenser is off, you will find manufacture manual papers for these steps and for programming of new control board (don't lose these papers for next time). Papers are located under bottom of front right corner of refrig where they are in a bag ( cut bag open and replace back when finished for next time). Replaced board by: 1. Pushing light cover to back to remove 2. Take screwdriver and push on two tabs that hold housing on at each side (will see two holes where they are by looking from behind, with your head inside) push and pull down. There it is 3. Replace board with the tabs that hold it in. (use latex gloves and only touch outside of board, to avoid static electricity to the board. 4. Reinstall and program (Code for your refrig is on cabinet sticker where model and serial no. are) 5. Install a surge protector on the plug for possible surges. Not too bad to install, just finding how it comes out .

The website, customer service, part, and one day delivery were very amazing to my husband and me. We will deal with PartSelect whenever possible. EVERYTHING re: the transaction including wonderful video instructions were A++ Many thanks

I simply watched the repair video and did it! Super easy, needed start device and capacitor. As easy as unplugging the old and adding the new. The video helped and gave me confidence. Wives can fix fridges too! Saved me $2500. Looks like I'll need a new excuse if I want a new fridge.

These plastic storage refrigerator racks can break relatively easily. Fortunately, the replacement of the center crisper rail is very easy. Just remove all the food items from the flat shelf above the crispers. The flat shelf (glass in our model) comes out as well as the crispers. When you remove the shelf and crispers, the center crisper rail is replaced by turning the frame upside down. It fits right in and is secure when you turn the frame upright. Don't try to make this replacement in situ, too many fragile plastic tabs that can possibly break.

Part Select's easy to use website helped me fine the part quickly and tips on change out. It was so easy, I only regret that I waited so long to so it.

Temp in fridge stayed around 45-46 degrees even at lowest setting. First went with most probable problem of replacing the Evaporator Motor Kit in lower freezer compartment, no change, next ordered thermistor in fridge area, no change, temp stayed in same range, then tried the Electronic Control Board in top of fridge, fridge works like a charm now. Very easy repair, just follow directions to progam new board. Possible cause a lightning strike near house that fried a TV about 2 years ago - fridge began to freeze items at first and went downhill from there.

After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.