59679213010 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sherril from ROBBINSVILLE, NC
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
FREEZEING UP
in stalled new circuit board an thermostat an was fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from VINEYARD HVN, MA
- Parts Used:
- W10827914
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Drawer door broke
It snapped into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from COAL VALLEY, IL
- Parts Used:
- WP67006878
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
The old shelf shattered when we tried to clean it
Just slipped it in. I think it's a very poor design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from SAMMAMISH, WA
- Parts Used:
- WP12227303WD
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My refrigerator vegetable bins were sagging when I placed veggies in it.
I came across this site and looked at the diagrams. Instead of buying a new crisper bin frame, I noticed that the crisper bin frame was missing the frame brace. I purchased the frame brace and installed it in the crisper frame, which was easy to push into the slot. This solved my problem. No more sag!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henning from RHINELANDER, WI
- Parts Used:
- WPW10128551
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Refrigerator was warm,freezer was cold
Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattaching rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Depew, NY
- Parts Used:
- W10830162
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Noticed fraying on the right side french door gasket and it didn't seem to be sealing like it should
When I received the gasket I laid it out on the floor in a spare room not too far from a heat register to let it straighten out. (If it were summer or sunny weather here I would have laid it out in the sun.) My adult son did the repair - it was very easy to pull out the old gasket and to gently clean the edges with a scraper to prepare for the new install. He followed instructions and other tips but the first section took a while before it would stay inserted. Once it did though, the rest of the gasket snapped in very quickly. I am happy the seal is much improved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from PRESCOTT, AZ
- Parts Used:
- WPW10503278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Freezer not defrosting and making fridge run warm.
Super simple following the instruction video you posted. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from SEASIDE, CA
- Parts Used:
- WPW10503278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!
I replaced the Control Board...
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Goldens Bridge, NY
- Parts Used:
- WPW10503278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Refrig. was not holding proper temp in refrig compartment
Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from BATH, PA
- Parts Used:
- WP67002633
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked humid drawer
Complete replacement of the plastic drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from SOUTH ST PAUL, MN
- Parts Used:
- WPW10534161
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Clips on old toe kick plate were broken on one side. Would not stay on
Took the new kick plate out of the box. Snapped it into position. I have had a repairman for this refrigerator before. I would rather repair an appliance than buy a new one. I'm very proud that I thought to get a replacement part myself instead of calling my friendly repairman again. Saved a few dollars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from CHIRENO, TX
- Parts Used:
- W11368721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Right Door Magnet weak, door would not stay firmly closed
Replaced seal on door. Same problem. Went to Lowe's and got several magnetic cabinet door catches. Attached them to the top of the door. (they can be seen sticking up), with the magnet part screwed to the door and the metal plate attached to a small wooden block glued to the top of the body with contact cement. Cost abound $16.
"To infinity and beyond."
"To infinity and beyond."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from WOODSTOCK, GA
- Parts Used:
- W11368721
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old gasket was worn out
Heated new gasket in dryer. Removed old gasket. Took less than five minutes per door and I am 78 years old!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Hardin, MT
- Parts Used:
- WPW10642944
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I scratched the door handle while moving the refrigerator into my house.
With a small allen wrench, I was able to loosen the two screws to remove the door handle and replace the new on without any problems. A very simple operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Live Oak, FL
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rear mount tab broken on Center Crisper Rail
It took longer to empty the glass shelf above the Crisper Bins than to replace the rail. Since the part simply snaps in place, no tools were required
Was this instruction helpful to you?
Thank you for voting!