25357188600 Kenmore Refrigerator - Instructions

First I removed one screw holding top hinge trim in place. I than removed two screws holding top hinge from refrig. I removed refrig door and laid it on a table. I than removed two screws holding the door stop and bearing hinge. I replaced the defective parts and reassembled in reverse order. Simple 10 minute repair.

I followed the video tutorial published here. The step I altered was setting the shrink wrap; I did not have a heat gun to safely shrink it, so I folded it tightly onto itself and wrapped it in electrical tape. No more frost buildup.

Watched repair video on plastic auger repair and decided to just invest in the whole replacement unit. 45 minute vs. a 5 minute repair.....no brainer. Removed shipping materials from new dispenser, placed on counter top. Removed old ice dispenser, dumped existing ice into new dispenser. Installed new dispenser with ice back into freezer. Tested and unit now dispenses ice.. Easiest fix I've done to date.

Could have done it with my eyes closed! Removed shelf and drawer, then removed broken support rail. Removed screw from broken rail and put the new, two piece rail together using that screw. Snapped rail back onto wall...returned shelf to fridge...returned drawer to fridge...returned myself to sanity! Yee Haw Easier than installing it was ORDERING IT. I was amazed by the ease of that process. Your ordering site is incredibly easy. By the way...I am a blonde and for blondes everywhere...Look at what I could do :)

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

I basically followed the instructions offered when i searched for the ice maker. It was relatively easy to do, I undid the 2 screws holding the ice maker to the side of the freezer, the was the tricky part, holding a mirror so i could see the slots of the screws. loosened them, disconnected the electrical connection and reversed the process for the install. It took about 25 minutes and i was back making ice.

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

Followed video instructions which were to unplug refrigerator, on lower back use screwdriver, loosen 4 screws, take off plastic cover, pull out fan, replace with new fan, replace cover and 4 holding screws, plug in refrigerator. I am female, 77 years old and if I can do it, anyone can.

Took off Door on Refr. and unscrewed Doorstop,
removed doorstop with broken Bearing and replaced with new Parts. Took about 20 Minutes
including reattaching Door. A 10 year old can do it.

Twisted replacement bulb into place easily. Let there be light!

Noticed the evap fan wasn't working, so trying to disconnect the wire broke the connection so had to order a new motor. Installed the motor but it still didn't work. Had a technician look at it and he said it was the control board. Ordered and installed control board and still didn't work. The only element left is the evap thermostat. Jumped the thermostat and it worked so ordered and installed a thermostat. It works now

Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!

Slid the shelf in place!

very easy to do. just snap into place

it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.