10632872010 Kenmore Refrigerator - Instructions

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

All food and drawers were removed from the freezer, including ice tray. The left side shelf brackets were removed to ease removal of the back panels which expose the the bi-metal defrost thermostat. Six screws to remove the large back panel, plus the shelf support rails needed to be loosened to remove the smaller upper panel. The bi-metal thermostat is mechanically clipped to the upmost coil of the condenser. The two wires must be cut and wires for the new thermostat spliced in. The wires were tinned with solder to insure a good connection, then twisted and crimped with an automotive end connector. With the smaller 22. 8 Cu. Ft. Refrigerator a lot of the work will have to be performed with one hand. The hardest problem here is diagnosing the malfunction correctly in the beginning. I was impressed that the replacement part was received in two days . . .

I spent several hours defrosting the unit. Making sure the vents were all defrosted and free of ice. The part replacement is fairly straight forward; remove the thermostat, cut two wires, reconnect the wires following color codes, attach to coil and restart. And, "Yippie!". Nothing. Zilch. Zero. Because I could not connect with the online repairman, I spent 40 bucks for nothing; problem was not resolved. Thanks for taking my money. I'm bummed and with just a little less money in my pocket. Never again will I ever purchase another Whirlpool product. Or buy from your outfit again (because of the over priced part). I replaced a 25 year old 'working' General Electric fridge for this junk that sat in the warehouse for four years before this was delivered to me in 2018 and sold to me as a "new" appliance. This was found out only when it crapped out and I needed to have it checked out for repair. Oh yea, I only had the comment section and the part recommendation to go by, and the latest comments are at least two years old. I'll be surprised if this even gets posted.

taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

shook bottle and painted waited a day and repeated

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

We had a refrigerator that had no ice maker at all, but it had the wiring behind the freezer panel and the wiring for the solenoid valve at the bottom of the refrigerator. The installation went easy for me, but I do not think the average homeowner could handle it. There are always little variations from model to model so some of the diagrams were not quite the same as my unit. But all the necessary parts and hardware were there and the install went fine. its crabnking out perfect ice like crazy.

Rather than pay a repairman an assessment fee, then the cost of the repair to the existing icemaker, I decided to replace the icemaker for a lot less. The Add On Icemaker kit came with installation instructions. The kit included the ice maker, as well as the hose and water feed control on the back. Originally, I was nervous about attempting to replace the icemaker. I watched a video on YouTube about replacing an icemaker and saw how easy it could be. Following the enclosed directions, and Wow!, it was extremely easy to remove and add the new icemaker. Don't pay to have someone else do it! This is a no-brainer.

unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.