Models > 25374229705 > Instructions

25374229705 Kenmore Refrigerator - Instructions

Jump to:

All Instructions for the 25374229705
106 - 120 of 528
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Callie J. from YORKTOWN, VA
Parts Used:
5304511738
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Freezer light bulb went out.
Used my hand to unscrew light bulb.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Heather from MCKEESPORT, PA
Parts Used:
242193214
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Door would no longer close
The old gasket was dirty and old and it had ripped, so the fridge would no longer close. The new gasket came in and all we had to do was push it into the groves and make sure it was secure, and it was fixed. Saved me hundreds of dollars buying a new fridge.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Danny from PUEBLO, CO
Parts Used:
241798231
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Drive great stripped for ice eject. Heater bad
Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Erin from NEW ORLEANS, LA
Parts Used:
242193214
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Old refrigerator door gasket was warped and door wouldn't stay tightly closed.
No tools needed. Popped out old gasket, cleaned/sanitizeddoor and popped new gasket into grooves. Door now closes tightly!!!
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from KNOXVILLE, TN
Parts Used:
241798231
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Ice maker would dump ice one time and then stop. Turning the ice maker off for a minute and back on would repeat the process.
I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from GROTON, CT
Parts Used:
241798231
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Ice maker stopped working. Part needed to repair it no longer available so had to replace the whole icemaker.
Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Marco Island, FL
Parts Used:
242252702
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Ice maker was over filling.
Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.
5 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jack from WALLING, TN
Parts Used:
241639502
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Socket set
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eldon from HALLAM, NE
Parts Used:
242252702
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Wrench (Adjustable)
During cross country move, water valve froze and broke.
Straight forward repair. Remove the four screws holding cardboard back. Remove the 2 screws holding the valve. Unscrew the water lines and unplug the electrical connections. I would caution that it would be wise to either take a couple photos or write down the order of connection. Even though it is somewhat color coded and the water lines are different sizes, a photo removes any confusion. My old valve had threaded connections using brass nuts and ferrules. The new valve has push in connections so you need to cut the ferrules off.. When cutting off the tubing, be sure to cut square. An angled or "squished" cut will leak when pushed into the fitting. Attach the valve to the refrigerator with 2 screws and replace the cardboard back and you're finished. While you have the back off is a good time to clean the coils. I left my fridge out and back off for a couple of ice making cycles so I could check for leaks (how I know the tubing needs to be cut very square). All in all, a very easy fix.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from San Diego, CA
Parts Used:
215846602
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The refrigerator wasn't cold enough.
I removed the plastic shroud on the ceiling of the refigerator, unscrewed and unplugged the old defrost timer, and replaced it with the new one. I reinstalled the shroud with the new timer installed.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sharon from Montague, MI
Parts Used:
242193211
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
moved into a new home and the inside freezer was iceing next to the freezer gasket.
purchased a new freezer gasket. It is still iceing in the freezer but now all over the top part and down the back. The new gasket does not secure tight enough around the entire freezer door when it is closed. It is secured properly to the door but does not "grab" tight enough when the freezer door is closed.
10 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
George from Cleveland Heights, OH
Parts Used:
240338101
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Needed to replace shelf
I can't believe I put if off so long... so easy to do and PartSelect was very fast, efficient, and the cheapest vendor for my part.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joel from SODUS POINT, NY
Parts Used:
242252702
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Wrench (Adjustable)
No water to ice maker
Repair was easy. Unplug refrigerator, turn off water to ice maker, remove back panel, disconnect water inlet valve, disconnect water supplies and electrical connections. Cut ends off tubing to modify to new part connections, connect tubing, connect electrical supplies, reinstall back panel, plug refrigerator in, turn water supply back on. We made sure that there was no ice build up in the supply tube into the ice maker and made sure that everything worked correctly before putting it all back together. It was an easy repair.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Arsen from Glendale, CA
Parts Used:
5303918202
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
i smell very bad smell coming from refrigerator
I started look inside ,disconnected power, and open all possible compartments to see any burned part. Fortunately I fined a small part look like melted and then i went online and make my research .Then i ordered that part and change it.
7 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Melissa from Olden, TX
Parts Used:
242252702
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Icemaker was producing hollow ice due to water was free flowing out the water dispenser during fill time for icemaker.
Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 25374229705
106 - 120 of 528