59672002011 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barry from FORD CITY, PA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer occasionally had a temperature alarm.Clicking noise also.
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Chelmsford, MA
- Parts Used:
- WPW10280613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken basket hanger
It was easy, remove clips and install new basket hanger and then just clip on the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Colorado Springs, CO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer and refrigerator compartments not cold enough
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PT CHARLOTTE, FL
- Parts Used:
- W10830189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Torn gaskets
Laid out new gaskets in sunlight to make them pliable. Removed old gasket by gently pulling them out of the channels around the door. I then did the reverse with the new gaskets. Starting at the top I pushed the new gasket into the channel, moving in one direction around the door. Make sure the outer lip of the gasket does not fold under itself. It should lie flat on the surface of the door. It is truly that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothea from TOMS RIVER, NJ
- Parts Used:
- WPW10534161
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Easy to clip in place
No tools required, but you must be careful not to shove or jam this kick plate into place as it is a plastic part and not really very sturdy. This is the second time I have replaced the kick plate and PartSelect has always been knowledgeable, polite, and helpful
!!
!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from KEWANNA, IN
- Parts Used:
- W10884390
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dripping ice maker
Replaced ice maker, but new one drips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from HELENDALE, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
freezer would not freeze
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Bismarck, ND
- Parts Used:
- WPW10655367
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
drip pan was cracked
Removed rear cover, removed fan and than drip tray. install new tray and reassemblied
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from ONEONTA, NY
- Parts Used:
- W10884390
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Replaced Ice Maker in Bottom Freezer
Looked at several videos on line in order to learn how to remove door and and all trays and bins and remove ice maker. Mostly straight forward. It helps to have a second pair of hands and eyes to assist. But could be done alone.Never did this before but I would say that, with a little courage, anyone could do this. I had a local repair estimate of almost $300. I did the job for the cost of the part, $80.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PHOENIX, AZ
- Parts Used:
- W11613295
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The refrigerator was working for just 1 minute and breaks, I discovered that the fan was not working , I understood that there wsa something wrong with the condenser fan motor. I just order a new one.
The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from SUAMICO, WI
- Parts Used:
- W10884390
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
no ice
Removed shelf, three screws on ice maker, disconnect elec. con. To Install reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MaryAnne from arroyo grande, CA
- Parts Used:
- W10830189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Replace worn door gaskets
Viewed easy online instruction video. Laid gaskets on flat surface and warmed with hair dryer until they were smooth and unwrinkled. Starting at the top I pulled off the old gasket and beginning at the top I snapped in the new gasket. Carefully smooth as you go. I'm a 72 year old women and if I can do it, you can do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from MIAMI, FL
- Parts Used:
- W10830287, W10830189, WP12722803W, W10443315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Condensation inside at the top of the refrigerator. Freezer compartment icing up.
Repair was very easy. I followed the instruction provided by this site for mullion rail. The door gaskets were a simple push fit. but needed the use of a hair drier to remove crimps in the rubber. Overall excellent. The refrigerator is working and cooling well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Dublin, TX
- Parts Used:
- W10830189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The refrigerator doors were not shutting well. . I would come home from work and the door would be a little ajar, but not beeping. The gaskets were cracked and worn.
I watched video provided on the part page. It was very easy to pull off the old gaskets. No tools needed. Also easy to push new gaskets into the grooves. I think it helped solve the failure to close program.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas J from WOODRIDGE, IL
- Parts Used:
- W10884390
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stopped making ice
Tested things a saw that the water valve was working so I figured it had to be the unit in the fridge. There was a possibility that it could be the thermostat or a couple of other possibilities. So I decided to replace the entire unit. That would be easiest and for sure solve the issue. It was simple since the new unit contained everything including the wire harness. So all I had to do was un plug the wiring connection remove 3 screws, remove the unit, put the new one in and plug the wiring connection in. Done in a couple of hours had ice. Within in about 24 hours ice tray was full. And works well
Was this instruction helpful to you?
Thank you for voting!