25364159402 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- eddie from CHICAGO, IL
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The refrigerator wasn't getting cold the freezer was getting to cold
Followed the installation instruction for both parts now both the freezer and refrigerator are getting cold
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Nevada, IA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken freezer door gin
Hah! It took 1 minute to open the package and 10 seconds to install. The shipping response was incredibly fast. Great Service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dari from ALBION, ME
- Parts Used:
- 240338201
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replaced a broken door bin
just pulled the old one out, and plopped the new one in. I was nervous about the new one being the correct size, but it was perfect. No fuss, no mess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from N LAS VEGAS, NV
- Parts Used:
- 240350609
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The glass shelf broke above the 2 drawers on the bottom
Just lay the new glass shelf into the groves. The shelf was too big and would not fit properly down into the groves.
Was this instruction helpful to you?
Thank you for voting!
Meat drawer rail broken
Removed the meat drawer and shelf from refrigerator. Removed 1 screw from right side rail. Slid rail forward and removed from slot. Inserted new rail into slot, and aligned with screw hole. Installed screw. Repeated process on left side rail. Reinstalled shelf into slots and slid meat drawer into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benton R. from Elkton, VA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hook on end of snap-on freezer bin broke.
The existing bin fell off when the hook broke as the freezer door was opened. Finding and ordering the replacement part was about as simple as it can be. Delivery time was less than a week. Replacing the bin was just a matter of snapping it in place, which took all of 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Grants, NM
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defrost timer was not working
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MONTGOMERY, IL
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Coils frozen over. Refrigerator not cooling
I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Salvador from SANTA ANA, CA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Freezer worked, refrigerator didn't. Ice build up on coils.
Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from STOCKTON, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator wasn't getting cold
removed the back panel of the freezer and unplugged the connector for the Motor. Removed the air diffuser, then removed the fan blade. Removed the 2 screws holding the motor to the bracket. Disconnected the old wire harness and installed the new one. Put the fan blade onto the new motor and installed the motor onto the bracket. Put the air diffuser back on, plugged the motor back in and fastened the back panel. Plugged the refrigerator into the outlet and tested, OK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from POMONA, CA
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken right side rail on meat drawer
Removed two top trays, fixed the rail on the second tray by removing one screw and sliding out broken piece, and sliding in new arm and rescrewing. Screw was a little tight, but went in.Very impressed i was able to do it myself with your simple instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Hayes, VA
- Parts Used:
- 241872512
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket failed
Simple. Just pull old gasket free from door. Pace new gasket on door and ensure that gasket is seated in the gasket channel all the way around door. This part fit door properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Okeechobee, FL
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Intermittent loud noise coming from fan motor located in freezer compartment
Ordered a new evaporator fan motor and watched the repair video supplied by part select on their web site.It was spot on step by step instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from LAGO VISTA, TX
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic runner broken
Got the part. Watched the video. Replaced the Meat Drawer Rail. Just lke that! Easy squeezy! Thank you for making it so simple! ***** (that's five stars!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earnest from BOWDON, GA
- Parts Used:
- 241872512
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket was damaged everything inside would freeze
Pulled the old gasket out and pushed the new one in.
Was this instruction helpful to you?
Thank you for voting!