1068490215 Kenmore Refrigerator - Instructions

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

After the front panel was removed, disconnected the timer and installed new in reverse order. The provided instructions could be more straight forward, I spent more time reading it than the installation itself.

First, after re-reading your descriptions here on your site ( it took clues from each of them) I unplugged the refrigerator and began on the only day my husband was out of town. The two selector knobs came off easily fingers only. The plate came off with only a slight prying with a screwdriver (it is intended to snap off this way). Loosening the screws and removing them in order to remember which order they returned proved to be a challenge. After disassembly, pulling the thermostat out of the tubing and replacing it with the new one without bending it was hard to do also. The refrigerator runs like new, and may run another eleven years! Thanks!

The repair was easy, I removed the cover on the top front of the fresh food compartment. It housed the defrost timer which was easy to identify and replace. Just removed a screw, unplugged the wires and replaced with the new part. Unfortunately, that wasn't the only problem. I also had to replace the defrost element that the timer sent power to. While I was at it, I replaced the defroster thermostat. The entire repair took under an hour, diagnosing the problem took the most time and effort.

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.

Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket

inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."

Just followed the Video I found on your site. Seems to work good now, took awhile to get temp setting correct (had to set it a little colder about half way between the "b" and "c" setting).

Repair video was excellent but thermostat unit was slightly different then original. Fortunately guessed right regarding connections. Also very difficult to place the insulating plastic on wiring. Not very smooth. Also removing panel was different then in video. Needed to remove the panel to reveal two screws underneath that need to be removed along with the ones at the ceiling.

Simply took broken pieces of old stud out and replaced with the new ones. Used pliers to adjust them. Replace a freezer stud and a fridge stud.

Important: Do not twist broken stud to remove if possible, just pull with the pliers straight out. I twisted it and made the hole larger. Even so, I just used Gorilla Epoxy glue to secure the new one (follow directions on the package) and it's fixed. It's been a couple days and still looks secure. Thanks for the quick delivery.

removed old and instaslled new. biggest problem was getting to one of the screws.

only the front right stud was broken with very little left attached to hold and remove. After a long twist and pull , got it out and placed the new one....

Still recommend Part Select..RAUL, MIAMI FL

your video made it very easy...Thank You