36368842894 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pedro from Miami, FL
- Parts Used:
- WR60X187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge not cooling
Fairly easy I pull the fridge foward and remove the backing board and notice the fan wasn't working, so I remove the fan and bench tested and it was burned then I clean the condenser with compress air if you don't have air then a vacuum cleaner works then once the part arrived I install it the now if working very good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MAE from FARMERS BRANCH, TX
- Parts Used:
- WR24X10236, WR24X10228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The old gaskets were not sealing properly.
removed the old gaskets with the putty knife to pry it loose then pulled the old gaskets off. Soaked the new gaskets in slightly boiling water to make them better able to straighten out and then installed by lining them up and pressing them in place, making sure they were lined up and that they were in the track provided for them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert L. from Eldred, PA
- Parts Used:
- WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy fan
Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles R from Renton, WA
- Parts Used:
- WR60X203
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The bottom part of fidge was warm with water droplets on the its ceiling.
Removed Ice shelf,
Remove rectangle cover by removing the two screws and lifting straight up.
Pulled fan off slowly.
Removed two hex screws holding motor bracket.
Remove cover.
Remove two hex screws holding remaining bracket from fridge.
Pull wire off motor noting where they were plugged in.
Pull apart brackets holding motor and remove motor noting how the motor and brackets fit together.
Reverse to install.
Remove rectangle cover by removing the two screws and lifting straight up.
Pulled fan off slowly.
Removed two hex screws holding motor bracket.
Remove cover.
Remove two hex screws holding remaining bracket from fridge.
Pull wire off motor noting where they were plugged in.
Pull apart brackets holding motor and remove motor noting how the motor and brackets fit together.
Reverse to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- N Smith from Chicago, IL
- Parts Used:
- WR24X10236
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
replaced the refrigerator door gasket
The original gasket had ripped and the magnet strip was hanging out. Following information from several youtube video clips & suggestion from the seller, I soaked the gasket in a tub of hot water for 30min to make it more pliable. After removing the old gasket, I put on the new, which only appeared to just snap into a metal tract. However the door couldn't seal. There were big gaps. That is when I realized that the gasket was still rigid. So I took a heat gun and carefully blew hot air on the gasket as I pulled it out enough for the metal edge of the gasket to attach itself to the refrigerator. Took quite a while to get it to seal correctly, but seems to be working well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- r from Bronx, NY
- Parts Used:
- WR24X10236, WR24X10228
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Gaskets needed replacement to maintain correct temperature in the refrigerator and freezer
Removing the old gaskets was very simple. Replacing the fresh door gasket was the most time consuming. It would have been easier if I had help, it took a some time and patience. The gasket works perfectly. The freezer gasket was easy to replace. The gaskets fit perfectly, thank you. For the ladies out there, you if I can do it, so can you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Seatac, WA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch wouldn't come out anymore and turn light on
Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lonnie from Covington, LA
- Parts Used:
- WR71X10378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
added an additional shelf
just pushed it in ! THANKS FOR THE GOOD SERVICE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Elizabeth, NJ
- Parts Used:
- WR71X2086, WR71X10378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing freezer shelf/wanted extra shelf for bottom
Easy. Unpacked the two shelves and installed them. No brainer. The speed of delivery however was exceptional. It seemed as if the order arrived here right after I submitted it! Really unbelievable! Keep up the good work!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gery from Tavares, FL
- Parts Used:
- WR2X7975
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bar end cap broke
Just snapped in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Leavenworth, KS
- Parts Used:
- WR2X9391
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
light would not stay on
First I flipped breaker to off position for refigerator, Pulled down on socket and broke it free. Then took needle nose piars to pull wire and plug out from hole, so I could conect to new light socket then snaped it in place . Hardest part was getting wire and plug out of hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Simpsonville, SC
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch quit working
removed the inside fridge electrical panel and swapped switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!