Models > 25331674102 > Instructions

25331674102 Kenmore Refrigerator - Instructions

Jump to:

All Instructions for the 25331674102
16 - 30 of 303
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Dennis from DEER LODGE, MT
Parts Used:
241798231
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Ice Maker stopped working
Reviewed the video on your website and followed the directions to the letter. Great video
38 of 45 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jerald from Phoenix, AZ
Parts Used:
242252603, 240331401, 240311502, 240311501
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set, Wrench (Adjustable)
Ice Maker water would constantly drip. Forming a huge block of Ice.
Pulled refrig away from wall, shut off water supply. Removed two screws holding the old water value on the back of the refrig. Removed the two water lines from the value. Hooked water lines up to the new value and bolted the two screws and the new value on. Turned on water and pushed refrig back into position. Simple and it worked. No more huge blocks of ice. I have Cubes!!!
36 of 52 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from Baldwin City, KS
Parts Used:
5303918277
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
The old ice maker had stopped working properly. The cycle was inconsistent, and inlet water would run over existing cubes in the tray, before they were dumped into the dispenser box.
This was really simple, much like changing a light bulb. Two bolts loosened beneath the old unit to allow it to be lifted off and free. The power supply plug was easily disconnected. The new unit was then placed onto the loosened bolts, power supply reconnected and secured with the supplied wire tie. A small angled bracket was removed from the old and reattached to the new as a support toward the from of the unit. The cycle adjuster was backed off a 1/2 turn as per the instructions....and the next morning....new automatic ice. Life is good!
28 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Cedar City, UT
Parts Used:
5303918277
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Old icemaker would not cycle to make ice.
I had already removed the ice maker by loosening the two screws with a 1/4" nut driver, in order to compare the design and style to the intended replacement for size and critical measurements. The replacement was almost identical. The wiring harness was 2-3" longer than the original, but after snaping the wire plugs together I simply curved the wire up and to the left to be out of the way. The hanging brackets are slotted and it was easiest to slip the back hanger over the head of the screw and let it slip down, then the front hanger was already to line up even though you can't see the screw with the ice maker in the way. I had to transfer an L-shaped metal bracket to the bottom side, matching the old assembly, and adjusting it to hold the bottom side away from the freezer compartment a little so it would hang level and secure. You have to snug the two screws with a screw driver or 1/4" nut driver by feel, since you can't see them with the icemaker in place. It took about 10 minutes to take out the old and another 10 to put in the new. We now have a full bin of ice, and the old plastic trays have been retired. I should have done this a year ago.
24 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from SIOUX FALLS, SD
Parts Used:
241798231
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Ice maker quit working
Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror
27 of 35 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
BARBARA from DIAMOND, IL
Parts Used:
242252603
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Water Was Not Being Sent Up To Ice Maker
I removed a couple of screws from the old part, and inserted the new part. Replaced the screws and I was done. No problem. I'm an almost 60 year old woman, and fixed this myself. It was so easy.
27 of 37 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ron from hawthorne, CA
Parts Used:
5304491941
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
freezer and fridge stopped cooling. Could hear compressor clicking on, smelled electronics overheating, starter melted.
remove the rear cover, and simply pull off harness and replace starter.
30 of 46 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
andy from Peshastin, WA
Parts Used:
240505801
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Refrigerator light was out
Test the light socket first with a bulb that you know is good. If the light still does not come on, unplug the refrigerator, remove the switch by inserting a very small, thin, flathead screwdriver alongside it and pull the switch out slowly with your other hand. There are two wires there. Remove them gently with some needle nose pliers. If you want to test to see if the switch is defective, take a insulated jumper wire, and attach it between the two wires. Plug the refrigerator back in and see if the light comes on. If the light does come on, replace with a new switch by re-attaching the wires and placing it back in the hole firmly.
26 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Farrell from Atchison, KS
Parts Used:
5303918549
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench set
Freezer worked great, refrigerator would not cool
Removed (unsnapped) plastic cover from back of refrigerator ( inside freezer compartment), determined that the fan was not turning, removed 4 screws from the aluminum back plate in freezer and tilted it down. Removed 2 screws with a nut driver, this allowed the fan to be removed, unpluged fan motor from the bace of the freezer and removed fan. Installed new motor and spent $38.00 to repair the refrigerator that would have cost me severial hundred dollars to replace. Thanks for the help
21 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeffrey from Bridgeville, PA
Parts Used:
5303918549
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
The bottom of Refrigerator would not get below 48 degress. Freeezer was working fine.
First I unplugged fridge. I then removed cover that keeps fan protected. I then removed 2 screws that hold the evaporator motor in place. I then removed 3 wires running to motor. Very easy to remove, just pulled connections apart. I then replace the old motor with new.

The Sears repairman wanted to charge me $359 to repair. I did repair for under $40! Amazing what you can save if you have the time and knowlege to do it yourself.
25 of 38 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Mount Royal, NJ
Parts Used:
5303918277
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Water in the ice bin freezing all the existing ice into clumps
You have to blindly unscrew the two screws along the side of the ice maker. Once that is done simply remove the ice maker to the side to gain access to the electrical plug. Undo the plug and remove the ice maker completely. Install the adapter on the new ice maker and install it in much the same way you removed the old. I started the (2) 1/4" screws before installing the new ice maker to make it easier to hang. Pay careful attention to the wire harness and dress it out of the way. Finally tighten the two screws and make sure the bail wire is down to begin ice making once again.
20 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jim from Au Sable Forks, NY
Parts Used:
5303918549
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
No air flow in freezer or fridge
Snap out fan cover, remove four 1/4" screws, remove back cover, remove defective fan motor, remove fan blade, install new motor and blade, strip wires and hook up with wire nuts, reinstall back cover, snap in fan cover, and plug in fridge.
21 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rebecca from Gautier, MS
Parts Used:
241559801
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Light Socket short
- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.
22 of 31 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JAMES from HENDERSON, NV
Parts Used:
5303918277
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Ice Would Not Work - But Water Disp Did
Shut off water/power - pulled tray -loosened two screws holding ice maker - lifted it up and off - unhooked power connection installed new maker in reverse of above - power supply line was much to long but just pushed it under the ice tray ( away from the maker ) prior to ordering looked at comments from others regarding installation
17 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Neptali from Groton, MA
Parts Used:
5303918549
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
Freezer is working but not the refrigerator.
Removed the cover inside the freezer. Found out that the motor/fan was not working. Ordered through PartSelect. Got the parts in 3 days. Installed it for less than 30 minutes. Very easy. It saved me hundreds of dollars. We considered buying a new fridge but not anymore. , it only cost me $70 including shipment charges. (Make sure you unplug the appliance first before opening the cover. Remember safety first.)
17 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 25331674102
16 - 30 of 303