25331447303 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from SOUTH LYON, MI
- Parts Used:
- 241798231
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker failed
Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from SAVANNAH, GA
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Not running
After waiting over 2wks for my part to arrive, I purchased the part locally and made the repair the same day as I am still waiting for the part to arrive from you guys. Your customer service really needs improving. I paid for 2 day shipping, what a joke. I will be returning the part as soon as I receive it thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Middletown, DE
- Parts Used:
- 5303918277
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice maker quit making ice
I basically followed the instructions offered when i searched for the ice maker. It was relatively easy to do, I undid the 2 screws holding the ice maker to the side of the freezer, the was the tricky part, holding a mirror so i could see the slots of the screws. loosened them, disconnected the electrical connection and reversed the process for the install. It took about 25 minutes and i was back making ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from parker, CO
- Parts Used:
- 5303918549
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Lightning struct the house and fried the evap thermostat
Noticed the evap fan wasn't working, so trying to disconnect the wire broke the connection so had to order a new motor. Installed the motor but it still didn't work. Had a technician look at it and he said it was the control board. Ordered and installed control board and still didn't work. The only element left is the evap thermostat. Jumped the thermostat and it worked so ordered and installed a thermostat. It works now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karine Lepold /BM CARGO from Miami, FL
- Parts Used:
- 241872501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer door gasket with a holes
/
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from AMES, IA
- Parts Used:
- 216954235
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Starter went out.
Unscrewed the lower back cardboard panel and removed it. Unplugged refrigerator. Reached in and took the metal piece off that keeps the starter from coming off. Pulled the starter off the compressor. Unplugged the starter from the power line. Replaced starter. Hooked power line back on. Hooked starter to the compressor. Put the metal piece back on to hold in place. Plugged refrigerator back in. Put back panel back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- harry from terre haute, IN
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
my old ice maker leaked at the bottom
it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fredia from Benton, KY
- Parts Used:
- 5304458371
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice would not spill into bucket
The repair was very easy. I loosened the two screws holding the icemaker onto the side of the freezer, then unplugged the icemaker. Reversed the order, and it was done. You have to shut the water off first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Azle, TX
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Original Ice Maker quit working.
Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness.
Installed the new one in reverse order and works like a champ.
Installed the new one in reverse order and works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denver from BLAIRSVILLE, GA
- Parts Used:
- 5303918549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Evaporator fan motor quit and would not circulate cold air from coils.
Remove shelves and rear panels to get to motor. Motor is held in place on shroud by simple strap. Remove fan blade, then un hook strap, remove and save rubber spacers on old motor to reuse to remount new motor. New motor Mew motor has wiring harness that is universal. Cut out the three wires that go to the new motor leaving long as possible, cut wires from old motor as long as possible, strip ends of all wires 1/2 inch, connect wires by color,slip into provided wire connectors and crimp. Pull on wires to insure connection. Tie wires together so they don't touch the coils. Plug in and check operation. If all is working unplug and replace all covers and shelves. Plug back in and it will take few hours to reach operating temperature. Video of side by side repair shows easy removal of panels and motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Woodstock, IL
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped working (Very oxidized residue)
I removed the old ice maker and unplugged the cable. Screwed in the new one with a 1/4 nut driver at the 2 mounting screws, plugged cable in. Checked ice maker with a small level before final. All Ok and after night I had Ice and it has been working great since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Otterville, MO
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
freezer frosting over,fridge warm
removed ice maker,,and screws holding back of freezer cover,unplugged wires and removed the cover and fan.wow,only wire to element had come unplugged!went ahead and replaced thermostat,and defrost timer,both were easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Smithfield, UT
- Parts Used:
- 5303918277
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
I replaced the icemaker
I removed the two screws and unplugged it. I then attached the pigtail to the appliance, then to the fridge. I had to push the excess wire harness into the hole in the back. It took a few minutes to move the rest of the harness out of the way by curving it upward and securing it with a nylon tie.I ordered the ice maker from Part Select on Sunday night and it arrived at 8:32 Tuesday morning, THANK YOU! I ordered very simple weed cutter parts from Sears a week ago and they haven't even shipped yet!
Was this instruction helpful to you?
Thank you for voting!