3639614280 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Torrington, CT
- Parts Used:
- WR32X10398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The shelf was seriously cracked and could not support anything being put on it.
I removed the old shelf and even though the new one had a slightly different texture, it fit perfectly and the two crisper drawers slid right in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Darien, CT
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker stopped working; would not fill
It was as easy as the instructions were clear (and they were). Remove 2 screws and two nuts, pop out the old ice maker, pop in the new, plug in and tighten screws/bolts. It worked. I'm happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Raleigh, NC
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker stopped cycling and wouldn't make ice
I removed the lower screw (not needed for the new icemaker), loosened the 2 top screws, unplugged the wire harness and removed the old icemaker. Unpacked the new icemaker assembly from the box, wiped the ice cube depressions to remove any debris, snapped on the water tube adapter, hung the new assembly on the 2 loosened upper screws and tightened the screws. The wire harness required the supplied pigtail plug which made the wire assembly long and awkward to replace the ice bucket/dispenser assembly, plugged it in and was done. It took a total of about 10 minutes for the entire operation and had a full bin of ice cubes within 36 hours and was ready for the ice dispenser/crusher in the freezer door. Easy install!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Columbus, OH
- Parts Used:
- WR30X10093
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
We can't seem to get the dripping water stopped when the water fills the ice maker. The large hole in the plastic we covered, but it still drips some. So we may try epoxy. An easy job we thought, but we have this water problem.
A friend had no problem getting the new ice maker in. But then the problems started. The ice maker works great. But when the water fills the ice maker it squirts water onto the side of the freezer and ice sickles form. So we watched and decided the hole was too large so used a piece of plastic. That helped to cover the hole. But some water is still entering the freezer and not all going to the ice maker. The only other thing we can think to try is to use epoxy to try to close that place. A simple job has turned into a big headache. I wish they made the ice maker like the original one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dudley from North Little Rock, AR
- Parts Used:
- WR30X10093
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
new part was substitute/which was some what different and was hard to get tray back in because power cord would not let it
i did every thing according to instructionwhich was simple but it did not cover how to use the extension electrical plug-in and where to put the extra cord so the tray would go back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Mattoon, IL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Icemaker quit making ice.
The parts were here the next day. After removing the old ice maker it was a simple installation using the adapter cord furnished. It took about 15 minutes. You have to work with the cord some to get it to fit behind the ice maker, but it does fit. The ice maker started up immediately & works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Brooklyn, NY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
My Icemaker arm was broken. It didnt move up or down by itself.
I removed the ice tub. Removed the screw on the left side that holds closed the section where the icemaker plug is connected. Disconnected the plug. Then removed the bottom right screw. I was then able to remove the Icemaker by unhooking it from the bcak freeze wall. I disconnected the icemaker from the fan gaurd. Removed the icemaker cover. unscrewed the 3 icemaker screws and opened up the chamber. removed the old Ejector Blade Drive Cam by removing the outer srew that hold the gear to the icemaker. changed the cam with the new one and reassembled everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Northville, NY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old ice maker quit
removed old ice maker, obtained part number from it. went on line ordered new ice maker at 10:45 in the morning, at 3:00 the nexte after noon new icemaker was in hand. took about 5 minutes to install new ice maker. works perfect. would do business again with this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Bismarck, ND
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Take out old ice maker and replace with new
Used the nutdriver to loosen two screws, life out ice maker, disconnect electric plug and put aside. Placed the new icemaker on the loosened screws, plugged in electric connector and tightened screws. Used small level to verify that unit was level.Waited about two hours for first cubes to be released into tray - has been working fine since!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stella from Manteo, NC
- Parts Used:
- WR32X10398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Veg. pan broken
The repair was very simple, all I had to do is take the old broken one out and replace it with the the New Perfect Fit Part. Thank you for the great customer service ane easy ordering process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Mount Ephraim, NJ
- Parts Used:
- WR32X10398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The shelf was broken.
Removed old shelf & put in new one.
It fit perfectly and looks nicer than the
original one. Also seems like it will be
easier to keep clean.
It fit perfectly and looks nicer than the
original one. Also seems like it will be
easier to keep clean.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Molly from The Dalles, OR
- Parts Used:
- WR32X10398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
It was a broken cover
It was as easy as removing the broken piece and replacing it with the new one. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patsy from Corpus Christi, TX
- Parts Used:
- WR32X10398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
pan cover was cracked, broken, telephone book was holinh the shelf up
Removed the old cracked shelf and slipped in the new one. Fit perfectly. Should have done this years ago !!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from el paso, TX
- Parts Used:
- WR32X10398
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Had a broken lower vegetable and fruit cover .
Simply removed all items on lower shelf then removed the old dried up lime that was used to prop the broken pan before. By the way it was placed there about 3 years ago.Anyhow tossed the lime cleaned the area and easily installed the new pan cover , Thank you Part Select .com i definetly will use u all again. Until the next broken part .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from MITCHELL, IN
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Icemaker Wouldn't Totally Work
Loosened 2 screws unplugged cable. Plugged in cable adapter on new unit. Plugged in to receptical, hung on 2 screws, tightened 2 screws. Done
Was this instruction helpful to you?
Thank you for voting!