10653352300 Kenmore Refrigerator - Instructions

This is a side by side fridge. Both refrigerator and freezer quit working. I could here the combination start device click and try to start the compressor. It would shut back off within 5 seconds.Removed the lower rear cover on the fridge and cleaned the coils while it was off. Replaced the combination start device, plugged in the fridge, and it worked. What a relief!

removed screws that held the ice maker in place, then removed the cover (popped off) The drive element was easy to remove, three screws and it was out. I put in the new part and reinstalled the icemaker with the three screws that hold it in place. I never call Sears for any repair. They use contract help and I have heard horror stories about those guys!

ridiculous how a tiny plastic broken part required a full motor assembly replacement. that being said, i went online, found this website and easily identified the part i needed to order. i was impressed when it arrived within a couple of days. removing the old motor and replacing the new was a piece of cake...and i am NOT mechanically inclined,

MAKE SURE POWER IS OFF or REFRIGERATOR UNPLUGGED BEFORE STARTING THIS!!!
I removed the lower refrigerator backing. The compressor was located in the left corner of the refrigerator. I located the start device which had a thin clip on top of it. After removing the clip I pulled the 2 wires (Red and White) from the start device. I then pulled the whole device from the compressor. You can use a screwdriver to pry it from the compressor. I unplugged the capacitor from the old switch and plugged it into the new one. Installed in reverse from how I took it out.

Excellent fit and installation. The door bins slid right in and created the extra space needed on the shelves.

First of all, you must remove two screws in the fridge compartment, and then remove the back panel in the freezer compartment which snaps off easily.

Then, you must push the four clips on the back of the diffuser together from the freezer side so that it slips out the fridge side.

Make sure to remember the parts as they come out, and re-connect them as needed to complete the repair.

This repair did not fix my fridge and so I'm drinking bourbon and trying to figure out how to fix this giant Kitchenaid piece of crap that freezes my beer.

Damn.

I watched several video's on youtube that showed me how to replace the parts. Just Google "how to fix my freezer". I figured the only problem was the freezer Thermistor so I only replaced it. The refrigerator has one to. Instantly the freezer went back to Zero degrees and the defroster works fine after melting all the ice in the bottom. Make sure the drain hole is cleared. I ordered the bi-metal thermostat just in case but I don't need it. Be sure and position the thermistor down in the freezer rail on the right side just to where you can see it in the first opening and pull it back up out of sight and tape it to the wall where it comes through from the air baffle. It's important that it's 7.8 " down from the top of the freezer. Happy now, Freezer 0, refrigerator 37. This thing use to run all the time, I'm saying electricity now.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

This company is WONDERFUL! I ordered the wrong drawer the first time, but their return process was a snap and the correct drawer arrived the next day. It's great to know that there is someone out there with just about every part you'll need for about any appliance that is truly customer friendly.

The star device that i recived was a little different, wasn't black like the original a recived a grey one and little bit smaller than the original but it fit perfect, and my frige is working good since i replaced.

Removed catch tray and then removed two screws that are underneath. I left the control panel hanging from its wires, then removed the two screws from the control bracket.
A word of caution before next step: You need to remove the two micro switches on the left and right. While trying to remove one, it split apart and the pieces fell out. I was able to put it back together and it worked fine. So be careful with the micro switches.
Continue tranferring wires and switches to the new bracket and reassemble in the opposite order.
An easy repair.

Approximately:

1. Unplugged refrigerator.
2. Emptied Freezer.
3. Removed Ice Maker.
4. Waited a few hours for ice to melt around back panel & nuts.
5. Removed back panel and the cover over fan and fan motor.
6. Waited many more hours for ice to thaw over fins, wiring, etc.
7. Easily replaced the bi-mental defrost thermostat.
8. Replaced panel, fan cover, ice maker.
9. Plugged in refrigerator and waited a bit.

This worked! Yahoo.

p.s. I am a 65+ year old mechanically minded woman. :-)

With the exploded (Printable) view of the assembly for my fridge available on this site, it was a breeze removing the existing ice dispenser motor and replacing with the new one. Ice dispenser work like new, now. I have never had a bad experience from Parts Select.

remove the front cover. everything else is a quick disconnect type of connection. Nothing to it! I would remove the cover and check these connections anytime the dispenser does not work. Look for broken or disconnected switches. This reapir took me a couple of minutes whereas the repair guy wanted almost 200 bucks to do this job. Parts ran around 30 with shipping.

New part slipped right into the studs and fit perfectly