3639550951 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cary from ORLANDO, FL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Ice maker stopped working
Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmie from Surprise, AZ
- Parts Used:
- 7C7
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb burned out.
Screwed new bulb in socket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from BRICK, NJ
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing
I just followed the instructions on the video and it was exactly as they said......no surprises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from HAYMARKET, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flapper was worn and misshapen allowing warm air in freezer, ice cubes to melt and drip and impairing function of ice dispenser. Frost formed in ice dispensing chute also.
Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flapper connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from Centertown, MO
- Parts Used:
- WR17X3160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Small grate on my ice dispenser broke
through away the old grate. Then put the new grate in the depression All done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from HAZELHURST, WI
- Parts Used:
- 7C7
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light bulb in my freezer door burned out.
Remove the burned out bulb and install the new light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from LEXINGTON, SC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Thought flapper in ice dispenser was problem. - more serious, more costly - not a DIY! New fridge here we come!
Opened, discovered not flapper but more complicated
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from SUN VALLEY, CA
- Parts Used:
- WR17X2061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Original part cracked allowing crushing fingers to grab plastic guide jamming it.
Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts as the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from SANDIA PARK, NM
- Parts Used:
- WR17X3670
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
On the water dispenser line, the heat from the compressor unit had cracked the feed line, resulting in a leak.
I removed the plate covering the water valve for the ice maker and water dispenser, removed the nut holding the 5/16" tubing to the valve and took off the tubing and nut. I did not need to turn off the water supply or unplug the unit. I removed the kick panel in the bottom front of the refrigerator, replaced the existing plastic fitting with a new push-on fitting, then spliced the tubing coming from the water chiller to the valve where the leak was thus bypassing the broken tubing with new tubing. I reassembled the valve using the original plastic compression nut, replaced the cover and ran the water dispenser while checking for leaks. The water dispanser works great with no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from HIGHLAND, MD
- Parts Used:
- WR29X5171
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
On/off switch stuck in the off position
Removed icemaker from freezer,
Removed 3 screws from cover plate, and removed screw securing main gear, removed gear.
Pulled back cover plate to expose switches and mechanism.
Removed screw holding switch to remove switch, and installed new switch.
I should have taken a pic of the cover plate, the interior mechanism and the wiring as I went along. It would have saved me 45 minutes in reassembly. Also, as luck would have it, I reversed the wiring on the switch. So off was on, and I had to remove it, switch wires and re-install.
But it works!
Removed 3 screws from cover plate, and removed screw securing main gear, removed gear.
Pulled back cover plate to expose switches and mechanism.
Removed screw holding switch to remove switch, and installed new switch.
I should have taken a pic of the cover plate, the interior mechanism and the wiring as I went along. It would have saved me 45 minutes in reassembly. Also, as luck would have it, I reversed the wiring on the switch. So off was on, and I had to remove it, switch wires and re-install.
But it works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Regina from Taylorsville, KY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
icemaker quit working when we moved
My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from BONAIRE, GA
- Parts Used:
- WR49X10183
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Ice Crusher began to leave plastic in ice
We only needed the rear plastic cylindrical helix. After installing it, there was a squeal of metal on metal due to insufficient clearance between the rear moving blade and the Ice dispenser plate.
Refrigerator Ice Maker 7/16” (or ½” hole, stainless steel) washer just behind #334 Rear Moving dispenser Blade PS292310 to give clearance so it doesn’t hit #345 / PS292441 Ice Dispenser Plate.
This was my first time at doing this so it took longer than someone experienced. But, it worked!
Refrigerator Ice Maker 7/16” (or ½” hole, stainless steel) washer just behind #334 Rear Moving dispenser Blade PS292310 to give clearance so it doesn’t hit #345 / PS292441 Ice Dispenser Plate.
This was my first time at doing this so it took longer than someone experienced. But, it worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACOB from COLLEGEVILLE, PA
- Parts Used:
- WR62X23154
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Only crushed ice. No cubed.
Found a step by step video on YouTube made replacement very easy. Cubed ice is back. Time for a cocktail to celebrate!
Was this instruction helpful to you?
Thank you for voting!