25336809890 Kenmore Refrigerator - Instructions

My fridge side had warmed up to 70 degrees but the freezer side was still cold. The coils inside had iced up. After thawing with a hair dryer, it froze back after another week. I removed the old defrost thermostat and wired the heater strip directly and turned on the defrost timer. It began melting the ice so that ruled out the heater strip being bad. I couldn't get a reading with my ohm meter on the defrost thermostat so I took a chance and bought the part. Installation was a breeze and it fixed the problem.

Having tried PartSelect.com before, I was very comfortable with the process. Input my symptoms and the feed back I received was that one of the 2 things (Defrost Timer or Defrost Thermostat)might need replacement. Since the cost was not much and over night shipping would cost more than the product, I decided to order both the parts. Changing parts was a breeze. The instructions posted by others on your web site were very easy to follow. You guys save me a bundle every time I have any thing going worng with any of my appliances.

Took old defrost pan off, put new one on. Had to bend new defrost pan a little for it to fit..

Simply popped the new end caps into place with the old guard and now it is tight and secure. Easy Peasy. Of course all this is after the operator at PartSelect ordered the right part for me; I had ordered the freezer door end cap, not what I wanted. I received the correct part the very next morning. Returning the wrong part was a breeze too.

Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!

attached the bar to the end piece and slipped it into the proper opening. Easy I ordered the piece one morning and received it the next morning. Great service.

door gasket: removed all the screws in the door panel,removed old gasket and fitted the new one and then replaced all the screws while making sure the gasket was in place.
Door shelf brackets: removed old broken ones and snaped the new ones in place.

From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.

Placed end cap on one end of rack and attached to one side of the door by applying hand pressure.
Inserted the other end of the rack into the end cap'
and again applied hand pressure to insert into slot, Repairs completed.

First I removed the old gasket by pulling it off the door. Then I removed the screws from the door. Next I placed the new gasket around the door frame. Finally, I replaced the screws in the door to completely attach the gasket.

took off the old one installed the new one

They were the wrong parts. I read a question another person asked and it advised to order these parts. Didn't want to waste my time anymore and threw them away.

After realizing the engineering on this dryer was different, I was able to access the temperature control thermostat through the front, along the side of the heating element. Several philips screws hold the front on, removing them allows you to take front panel off. At that point the heating element is below. I took a picture of the wires, so that when I started removing them, it would be easy to reconnect. Two screws hold the heating element in place, upon removing the heating element housing pulls gently forward and out, be careful of the wires, the thermostat is the second thing connected to the housing of the heating element. Two more philips screws hold the housing to the bottom of the dryer. Two wires are removed from thermostat, which is also held in place by two philips screws. Remove wires, one at a time and place on thermostat exactly as they were on old thermostat. Hold new thermostat in place with the two Philip screws, and reassemble in reverse order. And enjoy your working dryer once more, hopefully for years to come.

I unsnapped the old clips from the bar, installed one end cap to freezer door, clipped other end cap to bar, slid bar into end cap installed in door then snapped other end cap into place. Repeated for second shelf bar as those end caps were broken as well. No tools were needed.