10673209300 Kenmore Refrigerator - Instructions

Replaced drawers.

1). Pull Frig away from wall,
2). Unplug Frig
3). Turn off water feed
4). Remove cardboard dust shield on lower back
of frig (1/4" screws. I used socket)
5.) Valve visible attached with two1/4" screws to
Frig frame. (Remove two screws)Tip it is a good idea to hand tighten the two srews back into their original holes. This marks their placement for mounting the NEW valve later.

6.) Inlet Valve has three water lines attached to it
and two electrical clip-on wires.
7.) Stop work and take a picture of the Valve,
which clearly shows color coded clip-on wires
and hose connection ports.
8.) Take a break and study the photo next to
the NEW valve in order to insure an OEM
match.
9.). Note: Lines push directly into ports and then you need to pull them toward you, as though you were pulling them back out of the port. This will seat and seal the water lines with a tight fit.
Tip: Cut the old line about 2-3 inches away from the old valve and check that your cut is clean, before putting it in the portal of the replacement valve. Note: You only get it right the first time, so double check your cut is square with clean edges.
Look at the lines pointed straight at you to insure the plastic hose is still round. If it is oval or slightly creased at the edges, cut the hose with a razor blade or very sharp knife until it looks good and shove in fully, until it hits bottom, inside the NEW valve. Give a firm short pull and you will feel the hose seat almost immediately.

10.) Repeat the process with all three hoses
and take another short break. Look at your
photo to guide your color matching with the
Clip-on electrical connectors.

11.) Now remove the Clip-on electrical
connectors one at a time and place on the
NEW valve.

12.) Turn on the water feed line and check for
leaks. If NO leaking is detected, congratulate
yourself, and use two 1/4" screws to mount
the NEW valve to the frig frame. The two
screws you left hand tight in the frame, show
the way.

13.). Plug in the Frig. let everything settle in for 10
minutes, while you have a break for a small
bite/drink, use the bathroom, etc.

14.) Okay time to push the frig back against the
wall. Do you want to place the old dust
shield on the back of the frig? If you are
unsatisfied with the condition of the old one,
you might consider replacing it.

15.) My wife is good at crafts, so she chose to
use the old one as a template and made a
new cover out of material she had to buy.

16.). I should tell you that I had to do this job twice, because I bought a cheap valve online that looked exactly like what I needed. It failed to work with the ice maker and after three months, it started to leak. Once again I learned "you get what you pay for."

I hope this helps one or two people get it right on their first attempt.

Good Luck, Larry

First shut off water supply and unplug power. Unscrew icemaker assembly from side wall with 3 screws. Remove front cap and you can clearly see module. Unscrew and remove module ( only three screws). Install new module and revers procedure to finish up. Ice was ready in just a few hours. Video provided by this site was right on and left no questions.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

I added an icemaker kit. Everything I needed was in the kit. The refrigerator was presetup for an icemaker it was just never added. The only problem I had was that the holes for attaching the water solenoid were not pre drilled so I had to drill them myself and use sheet metal screws. The icemaker is working great.

Replaced the cap no tools needed

First took all frozen food out and than undid the screws that held back on--than cut the wires that held the piece and replaced it but also found that the plug was frozen so we thawed that out, that is why it took longer. Used air compressor to blow air and it broke it free and than we finished and put the food back after it got cold. So far it is working find and to beat all we received our part the next day so my husband could fix it that weekend--Thank you for the quick respond-
Patricia in Marengo Ohio

After taking apart the ice maker, the only obvious replacement was the motor assembly. I check various Internet sites and found the best price at PartSelect.

I removed the ice maker from the freezer after turning off the ice make switch. Removal was easy with only one screw holding in the entire assembly. The ice maker has rails that allow it to slide in and out like a drawer.

After R/R the motor assembly and returning the ice make to the freezer all that remiand was to see if it worked.

Within 10 minutes I had the wonderful sound of water filling the ice maker tray. Within 30 minutes of that, ICE!!!

Shopping, ordering and shipping of the part was fast and efficient. I'll go with PartSelect for all my future appliance needs.

I first read the instruction manual then I watched the installation video. My water line to it was 3/8. Went to the local ACE Hardware to purchase a short peace of 1/4 copper tubing and the fittings to connect them together. It makes ice every 55 minutes.

Open your door as far as it will go. Line it up with the plastic holder should just slide into place.

Ordered the new part, it was the perfect size and slipped right on to the existing brackets.

Took the glass shelf out of the fridge in our rental home to clean and it just shattered in our hands. Did a search online and found part select, phoned to make sure I was looking at the correct part, the lady on the phone was very helpful. I ordered the shelf using the next day service as we were returning home to the UK within 3 days so did not want to take the chance of not receiving it before we left. I got the notification the part had been dispatched, the part was delivered early next morning. Took the shelf out the package and placed in the tray, job done!. Great service will definately use again, have book marked the site.

Very easy to order from parts select. Took seconds to replace.

This was a simple install. I just replaced the glass shelf on the sliding shelf bracket.

Followed on line video