1068550 Kenmore Refrigerator - Instructions

3 Years ago our icemaker stopped working and we paid a professional $225.00 to come and repair. This time I chose to investigate the problem on line and PartSelect website gave me info on the motor assembly that may be the problem. Sure enough I purchased the part, it was delivered in two days. My husband installed the control & motor assembly in less than 15 minutes. We had ice within hours. Thanks for saving us a service call and the expense. The Goldbergs

removed icemaker timer/controler replaced with new part.reinstaled it works perfectly

Change motor on icemaker by taking the screw out the bottom ice tray so it will slide out once I remove the I took door off the icemaker it pops off. And follow the instructons for shower

Remove the ice maker with two screws in the side and one screw in the bottom. You don't have to completely remove the side screws but you do have to remove the bottom screw.
Lift up on the ice maker and reach behind it and unplug the wiring harness. The tube that lets the water in is accessible from the rear of the fridge. Remone the water line, its only finger tight, and remove the two screws. Pull the tube up and out. Thaw it out with hot water and reinstall. With the ice maker out and on the table, pop off the front cover. Remove two phillips head screws and slide the cube tray off. watch how everything is placed before you slide it off. Slide on the new tray and reinstall all screws. Reassemble in reverse order that you took it out. Your ready to make ice...

replaced icemaker motor.easy peasy

Removal of the Ice Maker required the removal of only one screw from underneath the maker and the power connector disconnect. Dis-assembly was straight forward. Remove old tray and heater, and reassemble with new tray and heater unit. Reinstall Ice Maker! Special Note: Allow the Ice Maker time to cycle through it's sequences. It may take a period of time before it starts producing ice after re-installation.

Went very easy, watched the video from the web site and did what it showed to do and put it together and it worked.We now have ice.

I removed the two screws that hold the ice maker door. I then removed the single screw on the right underside of the ice maker. I depressed the plastic "catch" on the left underside of the assembly and the whole thing just pulled straight out. I then disconnected the wire harness.

The module cover is removed, then the module itself is easily removed by removing three screws.
The assembly is just as easy.

A few hours later, I had a half bucket of ice!

The first thing I would like to say is thank you Parts select for a very fast delivery. It was within 24 hours I received my component. The installation went very well. The main thing is to take each part off the old mold, one at a time and install it onto the new mold. Make sure to look at each part as it is mounted to the old mold and re install them the exact same way. Just be gentle with some of the plastic pieces because they are fragile in certain areas. It will take a few hours for everything to start working properly. Thanks again Parts select. Good luck and God Bless.

First I replaced the thermostat. (from this company.) Same thing happened. Then I thought the ice heater has too low voltage and does not melt it for extraction. So, I put a short on the relay on the beam receiver board. No difference. Then completely disassembled the ice maker, and discovered the shaft cracked on the plastic gear, which rotates the ice extractor. So, I ordered and received this control assembly. Put together the unit and having ice again. Due to the cracked gear the thing was out of timing. This gear drives the contactor for letting water in, freezing time, heating the ice, (so it slides out easily), etc

Removed ice maker from freezer area. Motor in ice maker was not rotating ice dump bar. Replaced control and motor assembly. Problem solved.

Trouble shooted system and determined it to be Icemaker Control and Motor assembly. Removed and replaced assembly, but still would not make ice. Determined it to be the optics. Ordered Electronics Control Boards-Emitter and Receiver and removed and replaced both. Everything works now. Partsselect.com got my parts to me very quickly and their website helped me troubleshoot and select the correct parts.

i am not a mechanic so i tried to follow the video instruction. i am afraid that i am going to break a few parts or not able to put it back so i decided to follow instruction from other customer.
i used a phillip screwdriver removed the 3 screws after i turned off the refrigerator and remove the white cap that cover the motor assembly. the trick is to remove the motor assembly. it took me some times to shake the unit, remove the on and off handle from hole of the unit and carefully with little force pulling and shaking the unit it finally came off the ice maker unit. i placed the new unit by pushing it to the ice maker, replaced the on and off handle back in the motor assmble hole, screw the 3 screws back, cover the unit back, plcae the handle bar down to the on position. plug the refrigerator back and it started making ice after one hours. not quite easy.

my husband just took the motor off the existing maker and decided the front part of the unit was bad, I ordered it and it came in about 3 days he put the new front on it and screwed the unit back in the freezer, was about 4 screws I think. Didnt take too long but I would bet the next time it would be easier. Thank you

Followed the instructional video. It was not exactly like the unit I had but I followed as much as possible. I switched out the motor and within 3 hours had ice.