59657542791 Kenmore Refrigerator - Instructions

Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

Removed the two screws that hold flaping door. Removed the single screw that covers the connecting wires. Disconnected the wiring plug. I wiggled out the ice maker. Took off the motor cover. Swapped out one motor for the other. Reinstalled the icemaker in the resverse order of removal. Note the wiring plug in the freeze is very from. It makine s the reconnection differcult.

I didn't know what the problem was so replaced all 3 parts.
What I think actually fixed the problem is the Cold Control Thermostat that is not listed here. This part accessed by removing the dial control in the front of the Freezer. Part wasn't exactly the same but worked. I looped the sensor toward the front of the dial. Also replaced the Run Capacitor from the the back of the unit (Very Easy). Replaced the Defrost Timer from the Front of the unit (Easy). Now keeping 35-40 degrees in the Fridge and -15-0 in the Freezer. Nice. I plan to replace the Condenser Fan Motor also as it is a bit noisy.

replaced the bimetal defrost thermostat & defrost timer and that seem to cure the problem found repair easy and parts were here n lest than two days very satisfied with prompt sening of parts an explanation how to repair. Thank-you!!!!

removed the back panel inside the freezer (several small screws) with a nutdriver. used a hair dryer to melt the built up ice. replaced the thermostat and replaced the panel. very simple repair.

First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!

Service and shipping were fantastic! I would definitely use Partselect again!

Unplugged the refrigerator. Removed the screws from the access panel. Replaced the bad motor with the new motor. Works great . Probably saved myself $125.00 in a repair service call.

The web site and customer service from Partselect.com was outstanding. I had the part in two days. Their tracking system is wonderful.
First class company.......It's plain to see they put the customer first.

I didn't. Don't know how to get to light bulb to change it for this specific model

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

Disconnected power cord, Removed lower front face plate, removed one screw that helt cover over defrost timer, removed two screws that held timer, unpluged timer and removed it. Replaced old timer with new timer. Replaced timer installed two screws and replaced cover.

Loosened all retaining screws around gasket - removed old gasket - inserted new gasket and tightened screws. Little tedious (lots of screws) but very simple.